What's new
What's new
By:
Advanced search…

Recent content by Cannonmn

  1. C

    Need simulation of a motor design

    Friend needs someone to run simulation. Anyone know of someone who can run a simulation and get numbers for an electric motor. NDA work obviously based on the IP I have been working on. Simulation with any software is ok. Just need reports. The Engineer I hired on Upwork is starting to...
  2. C

    Does myasthenia gravis mean the victim should be terminated?

    Ok, u r correct of course, so maybe consider moving them to less dangerous job would be an alternative. I think if I ignored it and the MG-afflicted person is injured, I‘m guilty of negligence.
  3. C

    Does myasthenia gravis mean the victim should be terminated?

    This malady disrupts signals from nerves to muscles. It is treatable but not curable. How did or would you handle such a case? We have one now. I need to know if the victim is more likely to injure himself.
  4. C

    Milling Thin and Deep Channel on Vertical Mill

    Shishkabob before baking. Ordinary beam clamps were used to squeeze open end. A shim was placed in the slot to limit the amount it could close.
  5. C

    Milling Thin and Deep Channel on Vertical Mill

    I’m in same shop, took the liberty of editing Wakeless’ pic to see the difference in before (left) and after (right) baking. It is easy to see the unwanted V-shape on left and the desired parallel,sides of slot on the right. Unplated sheet steel was cut to cover both long sides of workpiece...
  6. C

    Milling Thin and Deep Channel on Vertical Mill

    Yes technically speaking the 24-in. Shaper is capable, we did think about that briefly but it fell off the chart because we’d have to make a special tool (cutter) and maybe a custom tool holder for it.
  7. C

    Milling Thin and Deep Channel on Vertical Mill

    I’m working on this too. Wakeless set this up on the horiz. Mill and it ran fine. He only took off about .300 per pass because we wanted to play safe given the 8” saw on a 1” arbor, and time wasn’t a factor. Some video:
  8. C

    Gage block cleaning

    Friend posted this on our local machinist forum but I didn’t see any good answers yet, so: “ Is a way to clean well used, old gage blocks that have small discolored areas (from light grey to almost black), but no where near complete sides or ends. These are working blocks, not top inspection...
  9. C

    Cinci no. 2 plain horiz spindle lock

    We put a short oak plank under one spindle lug, lower end sitting on rear flange of table with table cranked back against column. That totally immobilized the spindle in direction needed. Then a wrench with 3 foot pipe helper got it loose. We’d been using penetrant and some heat. Nut didn’t...
  10. C

    Cinci no. 2 plain horiz spindle lock

    Operator needed to remove arbor today, nut wouldn’t loosen, and he couldn’t find a spindle lock, I didn’t have time to go help, pls tell me whether there’s a spindle lock and where it is. I’ll make sure he’s turning it correct direction. We have manual but didn’t find spindle lock.
  11. C

    Expandable reamer stability

    Friend asked me how these reamers keep from wandering while reaming since the flutes are so much shorter than solid reamers with more flutes. No idea. Educate me?? Are the expandable reamers used differently than solid ones? Are results of the two types comparable? The rack in photo is...
  12. C

    Inventor wants to help us on his jobs in shop+sign NDA

    Thanks. Like anyone who has been in biz, we like to minimize risks, so the contract pretty much ensures we’ll get paid since payment in advance is required. We’ve also met with the person a couple times to see exactly how he wants to work, and all looks ok. We’d go thru a similar process...
  13. C

    Inventor wants to help us on his jobs in shop+sign NDA

    The client signed the contract above, no changes, and wired the upfront money. Appreciate the suggestions. You are welcome to send any of those undesirable inventors our way. https://www.capitolmachineshop.com/
  14. C

    Inventor wants to help us on his jobs in shop+sign NDA

    This part changed to incorporate Garwood’s suggestions and keep us from getting stiffed: 3. Payment Terms: Initially client pays kr for two weeks’ estimated services/expenses in advance ($xxxx.). Subsequent invoices will be adjusted by time worked. Work may begin after at least $xxxx Is paid...
  15. C

    Inventor wants to help us on his jobs in shop+sign NDA

    Thx, no deadlines. We charge 5 hrs/day max since that’s currently the length of our workday, but if client wants longer, maybe. We charge by hour. We may use the lines u suggest.
See more

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top