What's new

Recent content by Danvil

  1. D

    pc104 board replacment source? hfo says controler upgrade...no

    Hey I’m in the same boat, what was the conclusion on this ? Did you find a replacement, place to fix them, buy them ?
  2. D

    Haas Netshare output file in use

    Hey guys might be a silly question. I don’t know if I’m crazy and just making things up in my head, but I don’t think it was doing this prior. 07 haas Tm2 I normally keep my netshare tab empty and just overwrite the program in it, I set up the netshare again recently and I don’t remember...
  3. D

    Hitatchi Seiki rs232

    Thanks Colton. You are correct it was a cable connection issue ! I got it working with cimco and micro dnc2
  4. D

    Topper lathe fanuc 0-T control geometry issues

    I can’t seem to upload a photo off my phone, if my book, it says file too large. But my maintenance book says 5001-5128 are ( Settings of pitch error compensation for 5th axis.. Setting Range : 0 to +-7
  5. D

    Topper lathe fanuc 0-T control geometry issues

    Where do I locate the tool setter program ?
  6. D

    Topper lathe fanuc 0-T control geometry issues

    Hey guys 96 Topper Lathe Fanuc 0-T control Having an issue I can’t seem to resolve or figure out. I’ve been through the params and maintenance Manuel to no luck, now I’m looking for a smarter man than myself to help with my problem. Turret rotates to the correct T# , except when I teach the...
  7. D

    Hitatchi Seiki rs232

    Still haven’t solved my issue but these are the params/ settings for the LX3 that I’ve found and figured out. If anyone has any input it’s much appreciated. Param #6003 D7 = 1 tape device uses com module ( 0=PTR ) D6 =0 rs232 ( 1 rs422) D5,4: ( 5,4 =0,1 output port# rs232#1)...
  8. D

    Hitatchi Seiki rs232

    Hey guys Ht20sii Seicos L multi screen , yasnac Lx3 control Struggling to get the rs232 to input a program. I don’t see any options or settings on the NC Side, only place I can find is via editing, NC Prg input, on the multi side of the control. I’ve played with baud rates, data and stop...
  9. D

    Fanuc O-T issue

    Hey guys. It was the emergency stop.. It’s up and running! Only issue I have with it now is the offsets seem to read out of place Tool 1 reads offset 2 Tool 2 reads offset 3 And so on all the way down the list
  10. D

    Fanuc O-T issue

    Hey guys just got this Topper Elliot lathe plugged in for the first time. It’s fires up but stuck on this screen. “ 0669 - 06 Servo : 9046-09 PMC : C302 -F5 Copyright fanuc ltd 1988-1995 Not Ready “ Any advice ? I can’t find any help in my book..
  11. D

    Mitsubishi Meldas Lo control parts

    Message with what your looking for.
  12. D

    Greco systems mini file plus ss2 for sale

    As seen in photos. C300.0 plus shipping Open to offers
  13. D

    Hitachi Seiki Ht20s2

    Hey guys I have early 90’s Ht20s2 with live tooling that I’ve been trying to get back to life. John ( sigma surplus ) has been a big help and been very patient with me getting the params I needed and walking me through my disaster. Greg ( cyber machinery ) has been the same, big help and very...
  14. D

    Tsugami NM3 ( micro 5 ) Cnc lathe problems

    I did ! Thoughs loonies are ignoring me
  15. D

    Tsugami NM3 ( micro 5 ) Cnc lathe problems

    It’s a Mitsubishi control. Do you know any Mitsubishi whisperers hahaha
Back
Top