What's new
What's new
By:
Advanced search…

Recent content by Old Bus

  1. O

    Clausing 6300 FS in NJ.

    I'm cleaning out a few things, so I figured I would start by listing this here: Atlas Clausing 6300 Lathe I'll also have an old Waltham tool and cutter grinder project, a Carolina horizontal band saw, heattreating furnace, and who knows what else...time to use the garage for a garage. I know...
  2. O

    ISO MT4 Bull Nose Center

    If Skillet's doesn't work I have one, it's either a 4 or 5, but only 3-1/2" at the widest end. Just trying to help. Nick
  3. O

    AMMCO 7" shaper for sale in NJ $550

    The shaper is sold. Frank, I sold at Cabin Fever for about 5 years. It seemed like as the show got busier the quality went down, but the table prices went up. I finally gave up last year and made out better in the consignment auction, since I finally just about ran out of Gits oilers to sell! Nick
  4. O

    AMMCO 7" shaper for sale in NJ $550

    Hi Norm, Yup...I also put a few miles on a 4103. We used to have a fleet of antiques we used in a lot of movies over the years. Times changed and most of them are either in museums, or in some form of restoration...and sadle a few were lost to the scrapper. Frank, I do plan on going to...
  5. O

    AMMCO 7" shaper for sale in NJ $550

    Hi all, I've had this shaper a few years, it runs fine, but my needs have changed so it needs a better home, where it can be used and appreciated. As stated, it's a typical AMMCO 7", nothing fancy. It's covered in the typical machine shop gunk that has kept it from both rusting, and...
  6. O

    FS Rockwell 10" long bed lathe project in NJ $450 OBO

    Both the lathe and collets are sold and even gone! Thanks for all the interest. Nick
  7. O

    FS Rockwell 10" long bed lathe project in NJ $450 OBO

    Thanks for the info guys and Mencier, thanks for posting this for me in the Rockwell group. Hopefully I can try and keep this together without the agony of parting it out. I will seperate the machine from the collets, if that helps. Nick
  8. O

    FS Rockwell 10" long bed lathe project in NJ $450 OBO

    Bump for added photos
  9. O

    FS Rockwell 10" long bed lathe project in NJ $450 OBO

    FS Rockwell 10" long bed lathe project in NJ $450 OBO **PHOTOS ADDED** So my wife flipped out when this came home. I had planned on putting it back together and using it, but she said it was either her or this damn machine. I've had her up on Craig's List for 2 weeks and only one...
  10. O

    FS Van Norman "C" collets in NJ. $225 SHIPPED

    I have a rather nice selection of original Van Norman "C" collets for sale. These are the same as Hardinge 5V collets. There are also 3 pieces that are not V-N, at least I don't think they are, there are no markings. There is also an odd V-N collet. I believe all have been engraved with the...
  11. O

    FS Elgin lathe cabinet and underdrive, complete with motor in NJ $150

    I have a late 1930's, early 1940's vintage Elgin cabinet and complete underdrive. It was from a split bed lathe identical to the one restored on Tony's site. (Lathes UK) The back story is I sold the lathe several years ago to a friend in Missouri, but he never came back for the cabinet, which...
  12. O

    WTT (preferred) or sell SB(?) steady rest for Clausing 6300 steady rest.

    I bought a steady rest t hat the seller (not on here) said was for a Clausing 6300 12" lathe. Obviously he was mistaken! I BELIEVE this is for a South Bend lathe, but it measures 7-1/2" to center...so possibly a 14-1/2" machine? If anyone can actually identify it, I would appreciate it, but...
  13. O

    Hi, Simple question, just so I don't get my hand slapped. I would like to sell/trade a SB...

    Hi, Simple question, just so I don't get my hand slapped. I would like to sell/trade a SB steady rest for an Atlas/Clausing 6300 steady rest. I know Atlas is a no no but I wasn't sure about the Atlas/Clausing machines. Is it safe to post this request? Thanks Nick
    • Old Bus
    • Profile post
  14. O

    SB 13" pulley question

    Hi Guys, Thanks for the help, I passed all the information on, mainly the 2 pilley diameters. I can't wait to see how it all sorks out, I was just happy the machine was saved and not scrapped. Just to answer a few questions. The machine is a 1930 vintage so I assume it has bronze...
  15. O

    SB 13" pulley question

    Hi Guys, I recently sold a SB 13" lathe to a friend. It didn't have a countershaft, so he's building one with a spare 13" cone pulley I had lying around from a similar machine. He's trying to figure out what the drive and driven pulley diameters from the motor to the countershaft should be...
See more

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top