What's new

Recent content by olf20

  1. O

    Lagun Drawbar part number

    Thanks, appreciate the reply. olf20 / Bob
  2. O

    Lagun Drawbar part number

    A friend of mine has a Lagun FTV 2S. Looking for a drawbar for it. Anyone have a part number or? Thanks for any help! olf20 / Bob
  3. O

    Correct Motor Wiring

    I'm wiring a old milling machine up for a friend. No wiring diagram, but I took pictures of motor name plate and terminals inside pecker head. I look up on line and it seems to me it's wired correctly for 230V. Just want to be sure before I hook it up. Thanks for any help!! olf20 / Bob
  4. O

    Current to Start 20hp Ronk Phase Converter

    Got in touch with Ronk finally. They said 100 amp breaker would start it. Thanks for all the help. olf20 / Bob
  5. O

    Current to Start 20hp Ronk Phase Converter

    Need to test a Ronk phase converter at our shop. Need to purchase a breaker to test and need to know how big a breaker to get. I don't know any other specs yet. Thanks for any help! olf20 / Bob
  6. O

    Broke Torx in Blind Hole

    Got it done with a 1/8" masonry bit resharpened. Not bad at all. THANKS FOR ALL THE SUGGESTIONS! I learn lots from here. olf20 / Bob
  7. O

    Broke Torx in Blind Hole

    The torx is not loose. I know about the sobbing!! LOL I have read that a masonry bit is carbide and with a little sharping it will drill right thru. I have a cnc mill and will set it up in the morning and have at it. We need this done so the farmer (me) can get back in the field. To replace...
  8. O

    Broke Torx in Blind Hole

    No thru hole. Blind. It is a 8" round 2" thick 303 stainless. 4 bolt holes drill and tapped. This is on a liquid fertilizer unit and the bolts were pretty much ate away. I was lucky to get 3 of the 4 out. Now I'm trying to figure out how to get the last one out. Thanks for the replies!! olf20 / Bob
  9. O

    Broke Torx in Blind Hole

    Hi all, hope everyone is well! I don't post here very often but read alot and learn. I've got two 1/4-20 allen bolts broke off in 303 stainless. I drilled a 1/8" hole in the bolts right down the center. I tapped a torx bit in the 1st bolt, back and forth and it came right out. The second one...
  10. O

    A VFD for my Bridgeport

    I used the same drive. My first VFD. Learned quite a bit. So far so good. I don't do any heavy milling so will not tax the drive. I power it up every so often as I have read about some people having trouble with caps that have set for long periods. olf20 / Bob
  11. O

    Wj200015sf Saftey Stop. How to wire

    Thanks for the replies!! Reading thru the manual it gets confusing cause they have you jump from section to section for the details. I think the safest way is just to kill power as I have the breaker on the front panel of the drive. Thanks again for your thoughts. olf20 / Bob
  12. O

    Wj200015sf Saftey Stop. How to wire

    I have a Wj200015sf VFD running my Bridge Port Clone. I'm hooking up the controls and have the standard forward, and reverse hooked up. According to the manual when the run switch is opened the drive goes into stop. So far so good. Now what do I activate to ensure the drive won't...
  13. O

    Programing help with Hatchi VFD

    I have a wj200015sf. This is a single phase input. I got the mill running with the drive but I can not for the life of me find where to set the speed / frequency and store it, so when I power up the drive and press the run key on the drive it starts up to the stored setting. Lots of info in the...
  14. O

    Correct Splicing of Wires

    It's automatic. Put the circuits on the transfer switch to the max load of the generator and everything is automatic. Got 1/2 the wiring done. Thanks for the help!! olf20 / Bob
  15. O

    Correct Splicing of Wires

    Yes, transfer switch has 16 circuits. I have plenty of breaker space just need to lengthen some circuits. I've got the transfer switch installed and a 2" PVC conduit between new breaker box and transfer switch. Some circuits are in breaker box, but some have to go to the transfer switch. It's...
Back
Top