What's new
What's new
By:
Advanced search…

Recent content by ronaldinho_07

  1. R

    Hitachi Seiki TF15 Drive Alarm

    hello i have the same error as yours can you help me
  2. R

    Rebuilt flooded Mazak integrex 300 ll sy

    :green: half of the machine is in the water,the seller washed the machine before selling .And i dont know that part but not clean inside yes,water is going up to this place.half of the machine power on but not run the spind,the control still can start
  3. R

    Rebuilt flooded Mazak integrex 300 ll sy

    haha,in some cases,you have to use what you have. thats the fun part
  4. R

    Rebuilt flooded Mazak integrex 300 ll sy

    I have just bought a 2002 Integrex 300 ll sy without knowing the condition of the machine. And suddenly,i have heard that the machine was flooded ,almost 1/2 machine height... here some pics this is the rebuilt thread,i am not a expert ..i am just and end user.Trying to bring the machine back to...
  5. R

    help to clone mt640 integrex 300 ll sy

    my ssd is dead,have not backed up the os yet so i need your help to clone the os i willling to pay for it. is there anyone have ? thank you so much
  6. R

    5 axis machine questions

    anyone have DIY a 5 axes yet :D
  7. R

    Custom fixture for small/thin plate (logo)

    First of all,here is my testing product(have not cut yet) Yes.I have not used vacuum for small surface area yet,so i am very confused whether it works or not :confused: Yes,i am selling it,but for local fanclub here,trade mark is not a problem to me. I am planning for other stuff,similar like...
  8. R

    Custom fixture for small/thin plate (logo)

    I want to make this type of logo for example my current solution is: laser cutting the outside pattern then machining a small fixture that have the same laser cut pattern as above using silicon to paste the pattern into the fixture I want to make alot of this logo,so using silicon will take...
  9. R

    Is it possible to achieve 0.02(mm) tolerance when cut thin tube with wire EDM ?

    I have tried with laser cutting..and the tube is distorted because of clamping chuck
  10. R

    Is it possible to achieve 0.02(mm) tolerance when cut thin tube with wire EDM ?

    the weld because i want to make a workcell,fully automatic there are 2 problem : -bending thin wall titanium have big tolerance between the bends,so i can not weld on my robot -when you bend you need to cut both side of tube after the bend,waste lot of titanium tube Yes,i will try that way as...
  11. R

    Is it possible to achieve 0.02(mm) tolerance when cut thin tube with wire EDM ?

    thank again Marcus ! I will buy an old wire EDM and trying your advices,old chinese made machine (with new electric cabinet) is about 3700usd.In vietnam,they usually use molybdenum wire instead of brass wire,because the wire is reusable.Each molybdenum coil (about 2000 meters) ~ 25-28usd
  12. R

    Is it possible to achieve 0.02(mm) tolerance when cut thin tube with wire EDM ?

    I have cut other shapes ,solid steel,but workpieces is small.they cut seem ok,tolerance about <0.1mm but when cutting this pie cut type,in first 500pcs.I have measure ,the tolerance is upto 1mm :( i have classified them into 4 tolerances to use with different programs No.it doesn't that's...
  13. R

    Is it possible to achieve 0.02(mm) tolerance when cut thin tube with wire EDM ?

    I have made myself a robot for welding pie cut,but the robot is taught without laser vision.It only run (line,arc)what it is taught Each elbow included about from 4 to 8 pie cut,so example 0.02mm tolerance and i have to weld 8 pie cut total is 7x0.02 = 0.14mm at final weld .My acceptable...
  14. R

    Is it possible to achieve 0.02(mm) tolerance when cut thin tube with wire EDM ?

    thank you guys for all useful advices I am going to making a welding workcell (unmaned,fully automatic),for welding elbows for motorcycle exhaust pipe.So the biggest problem is accuracy of the pie cut.
  15. R

    Is it possible to achieve 0.02(mm) tolerance when cut thin tube with wire EDM ?

    I need cut alot of tubes. Its 1mm thickness,diameter from 25 to 51 mm. The cut will be like this. Angle of each side is about 7.5 degrees,so total 15 degrees/ 1 piecut. Example short side is 18.2,long side is 25.6 But when cutting,the tolerance is too big.It is upto 1mm tolerence The tube...
See more

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top