What's new
What's new
By:
Advanced search…

Recent content by Winterfalke

  1. W

    Shut down with tool in spindle???

    Might as well jump on the pile, HAAS VF2 had serious issues with the tool freezing in the spindle if left overnight. Once it was so bad we had the tool change arm get stuck, and flex so far the retaining button jammed. Had to dissassemble half the tool changer. After that, no tools left in...
  2. W

    Mazak tolerance issue in Automation

    We had a new multiaxis lathe brought in (think it was the Tsugami) that had temperature compensation, needed to hold a couple tenths in superalloy on a bolt shank. The machine swung over 20 degrees F during the day, and could never hold size when it did. Had to get their install techs in to...
  3. W

    Solid Carbide Shank Turning Tool Holders?

    I was told they need to cut both sides at once to stop warping, don't know how true that is. I've seen them cut on a normal lathe that worked great and I've seen them that potato chiped reguardless. As for the boring bar, I have seen one single bar that was solid carbide, brazed on steel...
  4. W

    OT LED tail lights

    I've spent a fair amount of time fighting with LED bulbs for automotive fitment, I can tell you they run the gamut from massively superior to downright idiotic. Buying name brand (Sylvania) bulbs of the appropriate type usually goes well, they can be a full radial light pattern and new ones...
  5. W

    tooling for repeat punching of holes accurately on Ironworker

    Drill .25 hole at center of first knockout. Install .25 dowel pin (or suitable locating geometry to drop into matching holes). Make locating fixture that dowel pin drops into for each location. Move dowel pin to first hole, punch, move to next hole, punch, repeat until done. Go back and...
  6. W

    Does ANYBODY use eBay anymore?

    If you are interested in building a better web page, I recommend concrete https://www.concretecms.com/. You can also just buy web page templates that you plug your own images and text into. If you want exposure, you need to learn SEO, search engine optimization. There are a lot of people...
  7. W

    how to machine the pocket radius in a top break revolver.

    It was the original die sinking process, you make a "cherry" that is shaped to match the pocket with file-like teeth on it. The cherry oscillated in a motion that drags the teeth in a cutting motion, then lifts up and advances forward again, similar to a shaper. The machine I saw just had an...
  8. W

    Where can I find forming taps/material displacement taps?

    I'm going to second Balax, we used them almost exclusively for tapping in a wide range of materials. Except the 8-32 helicoil tap, that one always gauged undersize for some reason. And form taps are not actually round, they have a lobular cross section that concentrates the forming forces and...
  9. W

    OT: Solar Panels for house

    My brother just had solar installed on his house. The relevant information is that he's in Florida, where they get enough sunlight to make it feasible, he has a new house with a new roof, it was done by Tesla and has their warranty (chinese made components, but they still warranty it), and he...
  10. W

    Who writes the website articles? Are they accurate?

    The only time I can remember using a radius gauge was hand grinding some lathe tools for turning plastic, inspection was always done on either the shadowgraph, the CMM, or using gauge pins.
  11. W

    Don't put your hands where you should not.

    At one point they dragged the short guy from the auto shop to help out running some of the machines. He was a pretty good bike builder, and a decent mechanic, but should'nt have been anywhere near the machines. He was doing some busy work between cycles, wiping down the lathes, and stuck his...
  12. W

    Machining PVC - Carbide tooling?

    I had a 10" round of grey PVC I had to take quite a lot off of, I just used sharp HHS and ran it fast enough the string was nearly molten, coming off shiny and cooling in the air. I just set up a shop vac above the machine to suck up the string. Pulled the resulting wad out of the vac and made...
  13. W

    Anyone ever watch these "machinists"?

    I've been complaining a lot lately about the horrible videos YT has been spamming me with like this, piss poor craftsmanship with garbage tools and ugly results, I don't care and it's certainly not "amazing technology" or "expert craftsmanship". And it all has the same horribad music with the...
  14. W

    Quick test to determine 6061 or 7075

    I wonder if the pyramid type hardness test would be repeatable enough to tell the difference across all the different alloys you have on hand?
  15. W

    OSHA Compliance During Set-up

    I had an incident where I was trying to grind a lathe tool bit by hand, and the safety idiot came by and yelled at me for not having the shields down over the grinder. I was told the grinder could not be operated without the shields in place, so when the plant manager came by I was just...
See more

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top