What's new

Search results

  1. D

    Yasnac MX3 drip feed - need help quickly!

    Or rerouting the communication cabling away from possible sources of interference. USB cabling is much more susceptible to interference. RS232 Serial communications (typically 15vdc signals) shouldn't be particularly susceptible to RF interference, but I suppose in extreme environments...
  2. D

    CRT to LCD Conversion on Yasnac LX3/MX3

    Well I had some time to mess with the 8200 ... along with a bunch more research ... I came up bupkis. Without knowing the exact format the yasnac outputs and the needed circuitry to convert the signals to something the less expensive 8200 can convert, all my attempts resulted in at best, a...
  3. D

    CRT to LCD Conversion on Yasnac LX3/MX3

    To answer my own question... From more reading I believe the difference between the 8200 and the 8219 is the 8219 can take the RDBI TTL input, where the 8200 cannot. I believe I can take the output from the Yasnac DF8100269 video board, TTL (5V) and convert it to VGA (0.7V) with a resistor...
  4. D

    CRT to LCD Conversion on Yasnac LX3/MX3

    I've got an old Mori mv35/40 with the yasnac mx1 control and I've been investigating this upgrade as well. Excellent write up...lots of good information I've found no where else. As far as the GBS8220 goes, I've read lots of complaints about them. From DOA to Chinese knock off of the original...
  5. D

    MV-35 Troubleshooting

    carefully vacuum the loose stuff then a soft bristle brush and rags lightly soaked with purple clean. Its slow but its the best chance of not letting a gremlin out. Dont spray purple clean on any aluminum you dont want satin finished.
  6. D

    MV-35 Troubleshooting

    Almost forgot... Probably the most important suggestion .. Something that would eliminate many of the threads on this forum. Find out how to copy the parameters from these machines. ESPECIALLY the hidden parameters that can only be seen and recorded by changing the rotary switch inside the...
  7. D

    MV-35 Troubleshooting

    Sounds like there may have been a cascading failure on the cp07 board. A possible option to consider are replacements from eBay, I have found several used replacements there for reasonable prices. Sad to see so many of these machines being scraped and sold for parts. The MV series machines...
  8. D

    MV-35 Troubleshooting

    document away ... Thats why im here ... just trying to pay it forward.
  9. D

    MV-35 Troubleshooting

    Parameter 7002 is "check of the keep memory writing completion during ATC cycle" 1:check 0: not check not sure why your setting was -127. Unless its different for the mx3 .. which it probably isnt. Either way it shouldnt be your problem right now. Check your messages Ive got something...
  10. D

    Send me your email ... the file I want to send is to big to post on the forum

    Send me your email ... the file I want to send is to big to post on the forum
  11. D

    MV-35 Troubleshooting

    Double check fuses, circuit breakers and cable connects to the power supplies. Might be something loose.
  12. D

    MV-35 Troubleshooting

    Let me see what I've got in my documentation ...
  13. D

    MV-35 Troubleshooting

    You can hope
  14. D

    MV-35 Troubleshooting

    If the machine hasn't run in awhile .. Limit switches might be a little gummy .. some wd40/pb blaster on those limit switches
  15. D

    MV-35 Troubleshooting

    I believe those are the ones .. You have to point the rotary switch in position 4I think .. The one in by the tape reader
  16. D

    MV-35 Troubleshooting

    I'm away from my notes right now so I don't know exactly what's going on but I think it's just a matter of getting everything re-initialized .. Possibly still a parameter problem .. Did you get the hidden parameters back in there also?
  17. D

    WANTED: Faro Arm Software Development Kit April 2001

    Archer, My apologies when I saw faro gold arm I assumed hobbyist ..
  18. D

    WANTED: Faro Arm Software Development Kit April 2001

    As a plan B, you should look into photogrammetry. Using a decent Digital SLR camera you can get equal tolerance results to the faroarm
Back
Top