What's new

Search results

  1. J

    Sp200 lincolin need tech help

    Changed 1 capacitor that was dead.cleaned with contact cleaner a bunch.now seams to be working.also when back to std drive roll.new kneraled drive roll where cutting wire bad no matter what I set pressure at.
  2. J

    Sp200 lincolin need tech help

    Ok played with it more. Strike arc on mig feeder still runs but it stops at tip no matter what v or feed speed.will bD cap do this how do I check them
  3. J

    Sp200 lincolin need tech help

    Thanks will check motor is 12v .if I jump speed pot should go wide open right
  4. J

    Sp200 lincolin need tech help

    Also welded for 5 hours at 23v 400feed .045 wire but feeds very slow
  5. J

    Sp200 lincolin need tech help

    Sp200 lincoln mig ok welds ok but feeder runs slow so can't trank it up. Ok changed brushs .new drive roll new liner and tip.new feed control board. .045 what up used it for 5 hr but it was very slow. Jim
  6. J

    Linde vi 206 welder question

    linde v1-206 mig welder need operation and setup manual bad enyone no where i get one need a manual bad for a linde v1-206 mig where can i get one ...
  7. J

    WTB: 1/4" Hex Broach

    hi dave fuchy ,hay if you see eny 5/16 broach hex over there buy me it i will pay you back with shipping jim
  8. J

    could you send me pics of the compresser will it run on a 7.5 hp motor . send them to...

    could you send me pics of the compresser will it run on a 7.5 hp motor . send them to [email protected]
  9. J

    flood damaged M head

    dump diesel over the top of it turn it by hand a little then roll the head over so motor is upside down the with a pump spayer cover it good with diesal fuel add 1 gt of oil to 5 gal . to help it . then leave it dry like this every week spray and turn it a little . it will be ok . my mill went...
  10. J

    Inertia flywheel construction.

    try here for dyno help TDK Motorsports Inertia Dyno Testing
  11. J

    What to use to clean a machine?

    dollar tree store the dollar store sell a spay for a dollar simply amazing is the name works great ......jim
  12. J

    FS- 1/2" and 5/8" Clear Acrylic Sheet Drops

    lexan plastic help enyone know where i can buy some cheep 3/16 or 1/4 in in 4x5 or 4x6 sheets does not have to be mint using it for a skid loader cab. jim need 4 pc
  13. J

    #2 pppppppppppppppppppppp

    #2 pppppppppppppppppppppp
  14. J

    who can do a internal 7/8 13 sapline in the end of a 13/8 x13 inch shaft for a pump

    so the trod would be .020 smaller in all areas .the trod orbits around how does that work cutting a spline . jim
  15. J

    who can do a internal 7/8 13 sapline in the end of a 13/8 x13 inch shaft for a pump

    1800.00 for shaft i told him i dont need to buy a new box .... may try the insert and weld im going to cut the shaft shorter and then make a flanged insert 1.093 id that way the weld will be 140 thick on flange . should work will press fit in shaft . insert in shaft soft then hardeen the...
  16. J

    Best solvent to clean dried honing oil ?

    how about a steam cleaner ..jim
  17. J

    who can do a internal 7/8 13 sapline in the end of a 13/8 x13 inch shaft for a pump

    would copper work better than carbon. do i make the noid size on size or smaller than shaft . how much do you allow for over burn ,how much noid wear on copper . on a 1.5 deep cut how long should it be ... jim
  18. J

    hi there ,im looking for someone with a shaper that can cut a 7/8 x13 sae spline in the end of...

    hi there ,im looking for someone with a shaper that can cut a 7/8 x13 sae spline in the end of a 1.375 by 11 long shaft its got to be 1.5 deep in a blind hole the hole can be as deep as needed . can you do this work . if so email me back at jfuchs3013@MSN>Com thanks jim fuchs
  19. J

    help with gear box repair guys

    gear box 10-4 still cleaning stuff almost got my storage garage cleared out but now i have tons of stuff to clean and put away. i put a lot of stuff in 5 gal cans with sealed lids . we oiled the stuff up by diping in diesal with oil in it then in the can what hap. is the temp change at the...
  20. J

    help with gear box repair guys

    gear box taping to the 5/8 works but this is a 1 time fix if it does it again the box is done . 2 holes on top and 2 holes on btm are in good shape .maybe i will thread the thinwall keenlocks in with a stud with green locktite . and then pin the stude in the side .. jim
Back
Top