What's new

Search results

  1. M

    Moving a Hexagon Optiv 2 Reference 2Z443 CMM

    Hexagon wouldn’t tell me anything about shipping preparation. they wanted me to get a service contract and pay them to move it for me and calibrate afterwards.
  2. M

    Moving a Hexagon Optiv 2 Reference 2Z443 CMM

    Well, here's what I ended up doing. Locked the two z axis by bolting alum plates from the lower frame to the bearing trucks. (I just drilled them out onsite with a hand drill). Then made up a plywood plate that fitted over the X Y table. Screwed carpet padded 2x4s to those for a tight fit. The...
  3. M

    Moving a Hexagon Optiv 2 Reference 2Z443 CMM

    Im moving a Hexagon Optiv 2 Reference 2Z443 CMM tomorrow. I don't have the manual for transportation but the OP manual I do have indicates that there are "transportation clamps" that fix the axis. Im trying to get the info from Hexagon but dont know if I will be able to unless I get a service...
  4. M

    2000 DMU50V Millplus won't get past I01 initialization

    As of today, if I start the machine, it will stay running for about 5 min if I dont move anything. If I reference and run a warmup program, I cant run for more than a minute or so. Either way, I get the X 53+ error which is "drive not responding" the + means a second error. That error is...
  5. M

    2000 DMU50V Millplus won't get past I01 initialization

    Im guessing it needs to have the caps replaced on either the output module, a bad IGBT, (ordered a new one), or bad caps on the DDC2 board. I searched far and wide for a manual on the Heidenhain DDC2 boards to figure out if I could swap test to another axis and there is no info on those boards...
  6. M

    Swapping Heidenhain DDC2 drive controllers to test - Simodrive 611

    Im trying to troubleshoot a simodrive 611 with Hiedenhain DDC2 optical drive controllers. I want to swap the DDC2 modules to see if the error (x53) follows to another axis. I searched both machine forums and the Siemens site and seems like no one has ever done this type of test. Has anyone ever...
  7. M

    2000 DMU50V Millplus won't get past I01 initialization

    Replaced the 16K31 contractor in the cabinet. One of three that controls the safety circuit. A used contractor but tested good. Started getting E60 and E61 errors along with the other ones. Swapped the relay out with the original and still getting the Z04 error when closing the door. Now...
  8. M

    2000 DMU50V Millplus won't get past I01 initialization

    So Im still getting X 053+ errors once and a while. I think its the X axis servo section failing. The error is "Drive not responding". This is a fatal error and requires a control restart. Im still getting the Z04+ errors when closing the door. This is a "Max following error too large". These...
  9. M

    Ok to mix rev version on Siemens simodrive Lt module 25 amp 6SN1123-1AA00-0BA0?

    Is it ok to mix rev versions on these drives? I see lots of rev A versions for sale on the used market but few version C. Im replacing a version C. Ive got the optical style modules installed in the 6SN1123-1AA00-0BA0 Im replacing.
  10. M

    2000 DMU50V Millplus won't get past I01 initialization

    Want to run a job today and the door safety switch started acting up. It does this once and a while and I just do a soft reset and proceed. Machine was running ok for an hour of two setting up tools before this happened. Then it threw a 53+ error and I had to restart. I tried adjusting the door...
  11. M

    S153 annoyance has devolved into S158 and will no longer operate

    I had a S173+ error on my DMU50V and it was a bad upper bearing. Pretty easy to replace, I wrote up a fairly detailed procedure here. The door switch is also a problem on mine. I think they eventually wear out and start giving errors. I also get random errors when the door opens or closes some...
  12. M

    DMU 50 T 1998 dnc problems

    I have a DMU50V with Millplus. I’m using a moxa ethernet to RS-232 converter. I am using the free moxa software. It works perfectly. You can get the maximum port speed of 56K with it. I have a post here that describes the install process and the correct settings for a millplus
  13. M

    Calbrating Laser Toolsetter DMG DMC103V SIemens 840D

    I think you're probably correct. I tried calling DMG support and they weren't interested in finding a tech to answer any questions about the toolsetter. They didn't even admit to knowing they had ever installed that type of toolsetter on their machines! Id just hate to run a calibration cycle...
  14. M

    Calbrating Laser Toolsetter DMG DMC103V SIemens 840D

    My 2000 DMG 103V with 840D control has a laser tool setter that works ok but can't measure the length of tools .125" and under due to misalignment in the Y plane. Been that way since I got it with only 180 spindle hours on it. Its very accurate in measuring tool length on anything larger than...
  15. M

    Cant make duplicate drive Hyundai HIT 840c

    Got the drive back. Works perfectly! I didn't even have to reload the MMC/NCK, still stored from last good boot I guess. For 600 I got a new 1GB industrial SSD, new DRDOS FlexOS, my hyundai files correctly transferred. Also, upgraded bios, I think to allow for larger drives or maybe SSD drives...
  16. M

    2001 Bridgeport EZpath III SL, Where is the backup battery for tool offsets?

    My lathe started losing the offsets once I power down. Still runs/boots fine but have to re-enter every power on. Cant find any mention online of what battery backs this info up and where it is. Of course, nothing in the operator manual. Also, the correct procedure to replace it. Anyone know?
  17. M

    Rotary axis speed way too slow Siemens 840D

    My post guy send a modified post over today and it now outputs correctly. Heres the output for the same part (.2" DOC instead of .1") that works fine. %_N_1105_MPF ;$PATH=/_N_MPF_DIR N1 TRANS X0. Y0. Z0. N6 G17 G70 G40 N11 G64 N16 T23 N21 M6 N26 G54 N31 TRANS X0. Y0. Z0. N36 S2000 M3 N41 G90...
  18. M

    Rotary axis speed way too slow Siemens 840D

    I guess my control is too old for that command, it stops at the FGREF line
  19. M

    Cant make duplicate drive Hyundai HIT 840c

    I ended up paying a siemens tech $600 to make a new SSD with my machines parameters from the initial image I created in DDrescue (ssd included!). Will update after it gets here. A lot easier than messing around with ancient HD's if it works.
Top