What's new

Search results

  1. P

    OKUMA OSP700L Program loading

    I finally figured it out incase anyone views this thread in future with the same problem. This is the method that worked for me. The steps on the controller are 1. press edit aux, 2. press PIP, 3. press read, 4. Type ",(what ever you want you program to be called.min, then press write. Then send...
  2. P

    OKUMA OSP700L Program loading

    As I said I'm using a laptop connected to the RS232 port. I am sending programs through Cimco, it says program has been uploaded but I can not see any data on the panel. If you can recall the steps that need to be taken on the controller would be much appreciated.
  3. P

    Okuma OSP700L Program Loading?

    First time doing a setup on an Okuma crown 762e. Control is an OSP700L. Can anyone advise me on the procedure for loading programs into the machine via the RS-232 port connected to my laptop. Also is there a specific file format this machine requires (example: My mazak's require programs to end...
  4. P

    OKUMA OSP700L Program loading

    First time doing a setup on an Okuma crown 762e. Control is an OSP700L. Can anyone advise me on the procedure for loading programs into the machine via the RS-232 port connected to my laptop. Also is there a specific file format this machine requires (example: My mazak's require programs to end...
  5. P

    Cambox replacement parts Integrex I200ST 2011 NEED HELP!

    One of our machinists crashed the tool changer resulting in a damaged cam box. More specifically upon further inspection after disassembly, the impact cracked a roller bearing in the center and has also made the precision fit hole for the .7" pin which the cracked bearing sits in oblong. The box...
  6. P

    kennametal dodeka shell mill speeds and feeds for 44w?

    Figured it out guys thanks for the help! The problem was I tried to use a high feed mill with facemill speeds and feeds. Spoke with kennametal again different guy told me I had to go way faster, 2000rpm / 0.070per/rev / 0.020 doc solved the problem.
  7. P

    kennametal dodeka shell mill speeds and feeds for 44w?

    I have tried many different variations based on suggestions from others, - 0.050 DOC, 0.008 feed per tooth on 5 insert, 800rpm -0.020 DOC, 0.003 feed per tooth, 950rpm - 0.030 DOC, 0.003 feed per tooth, 1690.225 (kennametal recommendation) -0.040 DOC, 0.008 feed per tooth on 5 insert, 800rpm...
  8. P

    kennametal dodeka shell mill speeds and feeds for 44w?

    Yeah its held in a 5 axis vise cerated hard jaws about maybe 3mm holding surface. We think this setup should work, as it is mild steel.
  9. P

    kennametal dodeka shell mill speeds and feeds for 44w?

    Doc is 0.020", machine is mazak vcu 500a 5x and stepover is 1in
  10. P

    kennametal dodeka shell mill speeds and feeds for 44w?

    Mazak VCU 500A 5X 2014
  11. P

    kennametal dodeka shell mill speeds and feeds for 44w?

    Mazak VCU 500A 5X 2 " W /0.020 DOC
  12. P

    kennametal dodeka shell mill speeds and feeds for 44w?

    Thats mild steel and kennametal said 885 sfm 0.015 per tooth (five insert). But that still doesnt work well.
  13. P

    kennametal dodeka shell mill speeds and feeds for 44w?

    Hi Guys, Just running a job right now having issues with feeds and speeds on my kennametal dodeka. Cuts sound super heavy. Does anyone know what I should run it at?
  14. P

    Tips for saving money on tooling for small jobshop?

    Hello Gentlemen, I am looking for some advice on tooling for our small job shop, more specifically I was wondering what would be some good ways to save money on tooling? All I have in mind right now is sending tools to get reground, but wanted to get as many inputs on the topic as possible. Thanks!
  15. P

    Troubleshooting 2011 Integrex Tool Change Failure (NEED HELP)

    Was running a job on our shop Integrex when the tool changer failed to pull a holder from one of the magazine pockets. The codes displayed are: - 265 Shifter Pocket Unclamp sensor malfunction - 1208 Tool Fitting Err (Cutting I.L) - 1295 Tool Missclamp sensor alarm - 1296 tool clamp error...
  16. P

    Where can I go to learn Solidworks and Mastercam? Is fusion 360 any good?

    As of now I currently work as an apprentice machinist doing dummy work (swapping out parts, deburring, little bit of manual machining.e.t.c) at a shop. However, in order to become more flexible, I want to learn how to program. The questions I have are: 1. Where can I go online to learn the...
  17. P

    Reading Suggestions

    Hey man would you mind sending me the list as well I am also interested, Thanks
  18. P

    CNC/Manual Machining content creators

    Just a quick question, as a rookie in the manufacturing/machining industry I want to dedicate all my time to learning the trade. Who are some solid youtubers I could watch to learn manual machining and also cnc programming/setup?
  19. P

    As an aspiring CNC Job Shop owner, where can I go to learn the trade?

    As of right now I’m a high school student finishing my final year. I plan to start my own CNC job shop as my future source of income. I have chosen to write this thread in this forum, as I hope some of you who have lengthy experience in the industry could advise me in what program I should...
Back
Top