What's new

Search results

  1. M

    '00 Integrex 200SY hydraulics and magazine wiring

    Hi The 200sy is actually what Mazak calls a mk2 machine. ( The integrex 30, 50, and 70 were the mk1) I have a 1999 version of the 200sy and I have lots of manuals in digital form if you still need them. Thanks Mark
  2. M

    Fusion 360 - Mazak 640t control

    I am looking for a good lost processor for an Integrex 200sy with 640mt control, so any help would be greatly appreciated!
  3. M

    New guy entering the CNC world!

    Hi, just my 2c on phase converters, it is worth the money to get a phase perfect digital 3phase converter. They are super expensive but are much better for the electronics of your machine. I have a hurco BMC2416 that I was running on in mechanical 3 phase converter but every time the spindle...
  4. M

    Advice on an 1998 Integrex 30?

    Hi, Thanks. I have seen them on youtube alot but not in person. Thanks. Mark
  5. M

    Advice on an 1998 Integrex 30?

    Hi, I am looking to add some turning capability to my business and considering a used maze act integrex 30. My 1st question is with the axes in their lowest position how short of a door can this unit fit under? My door is only a 101" is tall and from what I'm reading it looks like this...
  6. M

    Looking at purchasing a New Hurco VM1.

    Hi, I have had 3 hurcos and I love them. Their conversational programming is awesome, And if get one with a WinMax 5 controller it's even better than the winmax 4 that I currently use. When I do have to do something complicated I have my son draw a DXF file on fusion 360 and then do a DXF...
  7. M

    For Sale: 2 Kut HDM6 CarvLock 6" dual station vises on fixture plates

    Hi, I bought these vises for a job, but it did not end up working out, so I am selling these vises. They are Kurt CarvLock 6" Dual station vises. One vise has cast jaws and the other has Aluminum jaws. I also have one set of new Aluminum and one new set of cast jaws for these vises...
  8. M

    Wiring a Deckel FP2 to a Teco MA7200

    Hi, This may seem like a bit of a tangent, but just fyi, if you select #7 in Sn03 it will wipe out your programming in the ma7200, so just keep that in mind if you accidentally enter a 7 instead of an 8... (I found this one out the hard way and it has cost me big time) GOd bless...
  9. M

    Need some help w Teco MA7200-2007N1 driving my Hurco KMB1

    Hi, I bought a Hurco Mill that came with a Teco Westinghouse VFD model MA7200-2007 N1. Unfortunately the program for the teco got erased, so now I need to reprogram it to work with my mill controller. Motor stats 5hp, 120hz 3phase The mill is looking for some feedback from the teco cause now...
  10. M

    Need help reprogramming my Teco MA7200-2007 with my Hurco Mill

    Hi, I bought a Hurco Mill that came with a Teco Westinghouse VFD model MA7200-2007 N1. Unfortunately the program for the teco got erased, so now I need to reprogram it to work with my mill controller. Motor stats 5hp, 120hz 3phase The mill is looking for some feedback from the teco cause...
  11. M

    Need some help on a Hurco KMB-1 w Teco 7200-2007-n1 motor controller

    Hi I finally got my KMB-1 up and running today and it was working fine but after I came back from lunch the spindle would not work!!! (I left things powered up but just turned off the spindle) At first it was saying "ALARM DC. volt Low" I tried to clear the fault several times by power off...
Back
Top