What's new

Search results

  1. C

    Wiring mpg pendant to ML-15 lathe

    My Handwheels don't work very good. And it's easier to pick up material with a pendant, you can get right into the machine while doing it.
  2. C

    Wiring mpg pendant to ML-15 lathe

    Hello Everyone, I bought a MPG Pendant from Amazon and I was wondering how to wire it up? It's going on a Milltronics ML-15 cnc lathe and I was wondering if I can just wire it too the panel on the front with the mpg hand wheels and just wire it to the existing hand wheels and e stop. Also the...
  3. C

    Spindle Encoder Help?

    Yes and they want $950 for it, I'm hoping to find something for $200 to $300 in a replacement.
  4. C

    Spindle Encoder Help?

    My Milltronics cnc lathe spindle encoder needs to be replaced but the encoder company is no longer in business. Can anyone tell me what I can use as a replacement? Dynamics Research Corp. 152-121-1000-18WAS SERIAL NO. 5692443 Any help would be greatly appreciated. Thanks Mike
  5. C

    Milltronics ML-15 Jog Handwheel?

    It has the Centurion 6T control and it has the x and z axis mpg on the door, but it would be so much nice to have the hand held pendant. I will try to put a few pictures of it as well. Thanks Mike
  6. C

    Milltronics ML-15 Jog Handwheel?

    I have a 2002 Milltronics ML-15 cnc lathe and I would like to incorporate a jog Handwheel, I contacted Milltronics and they tell me that machine never came with a jog Handwheel, I would like to know if it would be possible to install one anyways. Any help would be greatly appreciated. Thanks Mike
  7. C

    Magnetek GPD 515 running wrong direction?

    Ok I figured it out, I changed 2 of the wires coming out of the vfd and that worked.
  8. C

    Magnetek GPD 515 running wrong direction?

    I have a Milltronics ML-15 cnc lathe and the spindle runs the wrong direction to what it should. I tried to switch 2 of the phases but all that does is makes the oil pump not work and still runs the same direction. I'm assuming it's a parameter in the GPD 515 vfd but I can't find it anywhere...
  9. C

    Graziano Sag12 24vdc clutches.

    I'm thinking about using a 24 volt dc power supply to run the clutches. Does anyone know how many amps that the 24 vdc power supply would need to be. Thanks Mike
  10. C

    Power Drawbar Stuck

    I have an old Excello CNC mill with a power drawbar, I'm trying to remove the drawbar but it seems like it's pressed in there or something. It's a 40 taper spindle, does anyone have any ideas? Thanks Mike
  11. C

    NMTB 40 Conversion

    I know this is a very old thread but SND I was wondering if you had a sketch of the Adapter for BT40 to nmtb40?
  12. C

    Allen Bradley 160-AA18NP03 Series C ?

    How do I post a picture on here?
  13. C

    Allen Bradley 160-AA18NP03 Series C ?

    Hi everyone, I am pulling my hair out trying to figure out how to get the 160-aa18np03 series c to work on my lathe. The VFD is a 7.5 HP and my lathe motor is 3 HP, I have it wired up and have a jumper wire set between 7 and 8 on the terminal block. I turn it on and the motor runs very slowly it...
  14. C

    Sag 12 Headstock Not Pumping Oil?

    So I took the top cover off and the oil is pumping fine, it was just hard to see it in that sight glass. Thanks for everyone's help.
  15. C

    Sag 12 Headstock Not Pumping Oil?

    Hi everyone, I finally got around to cleaning the Graziano Sag 12 transmission and changed the oil in it. I also drained the headstock oil and put fresh oil in it, got it wired up and it started right up, first time I have heard it run in almost 15 years. Now the problem is that the top sight...
  16. C

    Graziano Sag 12 oil pressure gauge?

    Sorry I forgot to put in that it's for the transmission oil pump, they pump around 70 psi I think.
  17. C

    Graziano Sag 12 oil pressure gauge?

    Just wondering if anyone can help me out, I have a car oil pressure gauge and was wondering if I could install it on my sag 12 on the transmission oil pump. And how it was piped into the oil lines. Thanks Mike
  18. C

    Waylube?

    I just looked on there web site and it's $20 something a gallon, was that a special they you found?
  19. C

    Waylube?

    Just wondering what everyone uses for waylube, can you just use a good motor oil?
Back
Top