What's new

Search results

  1. V

    Hurco VMX 24S Thrust Bearing?

    My Hurco VMX 24 is starting to make noise ( x axis ) near the motor so i believe. I wonder if it is doable to change it myself with proper guidance ( never done it before), or need to try an independent repair service. No hurco support near me. I have time. Lately its off most of the time...
  2. V

    VMX30 X-Axis Thrust Bearing Replacement

    Have you find a solution that can share? My VMX 24 is starting to make a louder noise also ( x axis ) near the motor. I wonder if i can change it myself, or need to try an independent repair service. No hurco support near me. https://photos.app.goo.gl/FrHAeB4GnQEVw6FJ8 Regards
  3. V

    Hurco VM-1 not booting - Black Screen

    Hi, Well, without visual it is a serious problem :) I would try to connect an comun pc monitor with VGA cable to its back. You will need to remove the screws and panels in its back Those monitors are pricey. There might be ways to trace the problem, but 2 days its short... There is someone...
  4. V

    Hurco VMX24s Ultimax4 dual monitor Panel swaap.

    Hi Just an update . I was able to replace the ccfl lamps and the inverter with a led kit. Its all working perfectly so far and for under 15 euros. Just a note. If intended to replace the ccfl lamps and keep the original lamps slider cover it is needed to purchase the led strips with 2 mm...
  5. V

    Urgent help needed with Hurco power on.

    Hi Sorry for late reply. I dont get any notification for updates on the threads It is located at the outside of the spindle box housing. Its a little red e-stop. In my case it appeared it was pushed out but in fact it had more room to travel. try pushing yours out a bit more. Photo attached...
  6. V

    Hurco VMX24s Ultimax4 dual monitor Panel swaap.

    Thanks for reply. So as I understand a 12.1, 12V 800x600 display with a VGA port would work. I just need to plug it to the VGA output port of the existing internal panel Board. Sorry to ask, how to supply the 12V power? From the existing Board itself or using the connector that goes to the...
  7. V

    Hurco VMX24s Ultimax4 dual monitor Panel swaap.

    Hi, Has anyone ever replaced the lcd(ccfl) inverter with a compatible one? Care to share? One of my screens is dying ( it turns on and slowly goes to black in a few minutes. sometimes very fast lately. Other option would be to swap with a LED panel, but as anyone ever done that? Looking for...
  8. V

    Need help with radius grooving.

    Thanks Gustafson, can you explain wich tool. I am also under the impression that it (the half circle )may only be possible by using a round (full radius) tool. I have a Sandvik lf123h25-2525bm tool available with parting inserts, however the round inserts for it are to expensive for me to...
  9. V

    Need help with radius grooving.

    Humm... Thanks, I will look into it. While i am at it, Can you please confirm that, to setup that type of tool for cutter comp on fanuc control i must use position 8 and specified the radius of of 1.5 for in this example Ø3mm full radius tool?
  10. V

    Need help with radius grooving.

    Hello, Self learning cnc lathe and I need help/advice on which tool and cycle to use for "grooving" a Radius. Control Fanuc OiT Machine Kia SKT 200. Thanks in advance. Regards
  11. V

    CNC chuck run Out and removal advice needed.

    Vacation is over and back in Business... I place an indicator over those 2 disks and this is what i get. Well i know its not good just don't know how bad. The sound it is not this evident near the machine. Is it the from the spindle? Or the phone is to sensitive? Shared album - valterMQ -...
  12. V

    CNC chuck run Out and removal advice needed.

    The main reason so far is that the chuck wobbles considerably and it seems i cannot dial the boring holes correctly to align the turret. Obviously it can be my inexperience on dialing this boring holes on the lathe with a dial indicator but i believe the chuck because it's wobbling gives me a...
  13. V

    CNC chuck run Out and removal advice needed.

    Hi, thanks for reply and for the manual. This part is certainly not the cover you mention. Photo1 shows the cover: photo 2 and 3 shows also a wedge part which i believe according to the manual is the chuck piston attached to the drawbar. In this case a special key with a wedge form is...
  14. V

    CNC chuck run Out and removal advice needed.

    Hello I have a Forkardt 3QLC/k200 power chuck mounted on a Super Kia Turn 200 that is in need to remove from the spindle. The main reason is the run out it outputs and need to check the spindle drawtube runout as well. Also for cleaning. On the plate 0.03mm, on the chuck body 0.08mm, on the...
  15. V

    Hyundai Kia SKT 200 Turret alignment

    I was thinking about a short ER collect, but i was wondering if the weight of the CoAx would not mater. I could also put an regular indicator as long as the tip reaches the inside walls of the boring holder.
  16. V

    Hyundai Kia SKT 200 Turret alignment

    Thanks npolanosky, i will try to do that, and yes you pointed that out(gridshif) in your video as well. My main focus is to align the turret and learn on the process. Cheers
  17. V

    Hyundai Kia SKT 200 Turret alignment

    No question is dumb, unless is asked by me. I hear you G-coder05, certainly a valid point and i totally agree with you. I am kind fixed on removing the tit that i might be changing the alignment of the boring holders. I do not have a Indicol but sure do have an indicator(2 at least) and a 3d...
  18. V

    Hyundai Kia SKT 200 Turret alignment

    Hi Today i was able to spend some time on the machine and made some improvement. I checked all the leveling and made a run to check the twist of the ways as per (Wes Johnson videos). All fine. Was able to remove the remaining pins. Used self made threaded rod device to pull the pins out...
  19. V

    Hyundai Kia SKT 200 Turret alignment

    Hi That is quite interesting also. Thanks for sharing. I will go align like you said in you video. I am just lacking some tools and time to do it properly. Was your turret this much difference before? From comments here, I am getting the impression that mine is way over than normal. Regards
  20. V

    Hyundai Kia SKT 200 Turret alignment

    Well a photo is worth a 1000 words right? I am getting an ER20 Monday. I will place a 4mm spot drill and see how the Boring holders align as well. Cheers
Back
Top