What's new

Search results

  1. 3

    Need a little more Help from Mits Guru's

    Nast555, well I tried exactly what you did, which is load G05 P10000 into the MDI, no joy, didn't get the same results. So hopefully tomorrow I will find out if my machine even has capability with the call to Mits. Thanks again for posting the pics.
  2. 3

    Need a little more Help from Mits Guru's

    Nast555, thanks for taking the time to show me that. I am going to give that a try this evening.
  3. 3

    Need a little more Help from Mits Guru's

    JCarroll, every time I have tried to run G05 or G05.1 I have always placed the command right before the X,Y,Z code of the actual machining bit. Much like NAST555's example. There are a couple of examples of splines commands in the book where you would also be using the G05 command in the...
  4. 3

    Need a little more Help from Mits Guru's

    Thanks JCarrol, it is comforting that you see things that don't exactly line up. On Thursday Friday, I will be calling Mits. I'll report back what I find out. KC
  5. 3

    Need a little more Help from Mits Guru's

    Thank you very much ranchak. I will give them a call. yeah the controller part is hard to understand as well. First pic on this thread I posted a screen shot of the PLC version as broadcast on the screen which shows Meldas 64SM, but the splash screen shows Meldas 60S KC
  6. 3

    Need a little more Help from Mits Guru's

    Hi Guys, thanks for chiming in again. Thanks Atomkinder for bumping the thread. Looks like my best bet is to call Mits. That being said, does anybody have a contact, I have tried to call before but I have never reached the right place. Not to beat a dead horse but here are some...
  7. 3

    Need a little more Help from Mits Guru's

    Hi Everyone, I have a Akira Seiki Proforma with Mitsubishi control (2003) I am trying to figure out what PLC I have exactly. The splash screen at start up says "Meldas 60S".. However, the physical PLC says FCA64S as does the Config screen. Reason I am asking is the Manual for a 60S...
  8. 3

    Hope to find a Mitsubishi Meldas 64 GURU

    Thank you everybody for taking a look and any help you have provided, Vancbiker, Atomkinder, Ewlesy. I think I have found the issue and fixed it. At this point I have put 100 tools through the spindle testing without error. So I am 99% sure I got it licked. What is was; There were a...
  9. 3

    Hope to find a Mitsubishi Meldas 64 GURU

    Thanks Vancbiker, thats what I was afraid of. Does your bike require the use of spandex or leather?
  10. 3

    Hope to find a Mitsubishi Meldas 64 GURU

    Sorry that turned out sideways but you get the point. Should have turned the phone. My orig. install book (not filled out on my install) has all those fields as you see them in the picture. In other words the Tech that set it up didn't make any changes to those fields either (which doesn't...
  11. 3

    Hope to find a Mitsubishi Meldas 64 GURU

    Vancbiker, Ok I found what you are talking about. Yeah there is zero data in there for setting basically 00's or nothing at all.
  12. 3

    Hope to find a Mitsubishi Meldas 64 GURU

    Thanks for getting back Vancbiker. You say PSW (position switch) page I am not clear where that is at unless you mean setup. In setup I have: Z axis #2014 = O/T+ - 139.500 #2015 = O/T- - 299.500 #2073 = ZRN_DOG (00) #2014 = H/W O/T+ (00) this is the alarm #2015 = H/W O/T- (00)
  13. 3

    Hope to find a Mitsubishi Meldas 64 GURU

    Hi All, This is my first post but I have lurked Practical Machinist for years. I hope to find someone with Mitsu 64 experience, that can and is willing to help me out. I have an issue with tool change out routine on a mill that is new to me, and actually quite new hour wise (300) total...
Back
Top