What's new

Search results

  1. J

    WTB #12 Jarno to Morse Taper Spindle Adapter for 1962 Monarch 10EE

    Hi all, As the title explains, looking for #12 Jarno to Morse Taper spindle sleeve/adapter for my 1962 Monarch 10EE. Thank you.
  2. J

    What is the in Internal Spindle Taper on a Whacheon WL-435 17"x40" Lathe with A1-6 Spindle?

    Good Afternoon, I have done quite a bit of searching but I am not coming up with any solutions. I have a Webb/Whacheon (Korean made Mori Clone) WL-435 lathe and all the literature I have read including the owners manual say the internal spindle taper is MT6. Thinking it meant Morse Taper, I...
  3. J

    Wanted-Manual for D'Andrea Boring/Facing Head

    Good Evening, I came across a D'Andrea TS - second version boring/facing head with manual and automatic feed. It's in pretty nice shape, no corrosion on the head but there are a few dings and scars but everything moves smoothly. I believe all the original accessories are present but they are...
  4. J

    Spindle Lock Switch Question on 1962 Model 10EE

    Good Evening, Please forgive me if this is a stupid question but how do you test if the spindle lock switch is working properly without damaging the lathe? If you engage the spindle lock and attempt to start the lathe, if it is not working properly, don't you risk causing serious damage...
  5. J

    Opinions/Guidance on Three Jaw Chucks

    Good Morning, I know the subject has been beat to death and I have searched and read as much as I can on the subject. I have a 6" 3-jaw Bison Set-Tru chuck that has seen better days. After dialing it in on a specific diameter part, it will not repeat on the same part and is off by several...
  6. J

    Help with Blake Coaxial Indicator

    Good evening, Several years ago, maybe longer I purchased a brand new Blake Coaxial Indicator. It's been in my tool cabinet since and other than periodically opening the case to be sure there is no rust forming I have never used it. You can imagine my frustration when I took it out of the...
  7. J

    Oil or Grease on this Monarch 10EE apron?

    Hi All, My new to me 1962 Monarch lathe has a fitting on the apron for lube. I assume it's for oil but the manual does not show it and I am wondering if it is in fact an oil fitting and if so, way lube? Photo below and thanks in advance for the help.
  8. J

    1962 Monarch 10EE Drive Issue

    Good Afternoon, I recently purchased a 1962 Monarch 10EE from a very nice forum member. I finally picked it up and wired up to 240V single phase as required and it does have Scissio Solid State replacements installed for the Thyratron tubes. I started it up today for the first time and began...
  9. J

    WTB - D1-3 Backplate for Adjustable 6-Jaw Chuck

    Good morning , all, I have a nice 8", 6-jaw adjust-tru Buck Chuck that I'd like to use on my recently acquired Monarch 10EE. Looking for a D1-3 backplate that I can mount it on. Thank you, Joe
  10. J

    Help Identify This Hardinge Hand Tool?

    Good Afternoon All, Included with a my recent K.O. Lee tool grinder purchase was this hand tool with no markings other than Hardinge, Elmira NY. Anyone have any idea what it's used for? Thank you. Joe
  11. J

    What size tapered reamer is needed for a KO Lee grinder?

    The next step in making the new part for my K.O. Lee Grinder is to drill the tapered holes for the table locks. I believe a tapered reamer is what I need and since I will need to purchase one, I am hoping to confirm the size I need. The table lock tapered pin (photo below)is .794 inches long...
  12. J

    Advice on how to make a part for K.O. Lee T&C Grinder

    Good Morning, All, I am moving forward cleaning and repairing my recently acquired K.O., Lee B960 T&C Grinder. I came a cross a part that locks the swivel table down that is cracked and was some what repaired. Adise from it being cracked some of the holes for the table locks are also cracked...
  13. J

    Source for Tab/Keyed Washers for KO Lee T&C Grinder?

    Good Afternoon, While working on my new to me KO Lee Grinder I notice the nub on keyed/tab washer on one of the shafts is just about gone. It took me a bit to figure what that type of washer is called and searching the forum and using Google has not resulted in identifying where I can purchase...
  14. J

    What lube/oil to use in KO Lee B943 Work Head?

    Hi All, The title says it all, trying to figure out what the proper lube is for the KO Lee B943 powered work head? Everything I have read makes no mention of it. Any guidance, comments, opinions etc. are most certainly appreciated. Thank you. Joe
  15. J

    Help with Replacement KO Lee T&C Grinder Motor Switch

    Good Evening, Still working on my recent acquisition of a KO Lee model B960 T&C Grinder. The toggle switch for the work head needs to be replaced and I'm not sure of a source for it hence my inquiry here. The switch mounts (photos below) to the housing using two small screws and after quite a...
  16. J

    Help Identify Starrett and OK Tool Tools

    Good Evenong, all, I have asked for and received quite a bit of assistance with my recently acquired KO Lee B960 Grinder and I am most grateful. As I may have mentioned in previous threads, the seller was most generous and sent a lot of tooling and accessories. While going through some of it...
  17. J

    Help Identify This KO Lee Grinder Accessory

    I'm back again, I hope I don't wear out my welcome. I continue to unpack the many items the seller sent with the grinder and I came across a few of the items picture below. I am not sure what these 5C taper gizmos are? Thank you, Joe
  18. J

    Question About Norton Brake Controlled Truing Device

    Good Morning, I'm back once again seeking to tap into the wealth of knowledge of the members of this site and I am most appreciative. Along with my recent acquisition of a KO Lee T&C Grinder was a Norton Brake Controlled Truing Device. Along with trying to figure out how to use it I am...
  19. J

    Help Identifying What Taper Tooling I have?

    Good Afternoon, I recently purchase a KO Lee B960 T&C Grinder that came with quite a bit of tooling. It has a 5C powerhead but most of the tooling (chucks, faceplates etc.) appear to have a different taper (larger). I attached a few photos to help identify what the taper is on the tooling. I...
  20. J

    Type of Oil in Headstock of Whacheon WL-435 Lathe

    Good Morning, All, I know this subject has probably been beat to death but I have done quite a bit of searching and I see varying opinions on what type and weight oil to use in these lathes. I checked the manual and it recommends Daphne Mechanics oil 44, I can't find that oil and I am not sure...
Back
Top