We replaced the 4 D cell batteries in the mill this morning after receiving the 307 alarm and a low battery alarm. Once we restarted the mill we check the messages and the following message was present. "2199 Check the EOP ROM files".
Does anyone know what this means? It may have always...
Does anyone have any recommendations on a engineering sight similar to PM?
I have found eng-tips and engineers edge? Are they any good? Any other recommendations?
I am looking to build a machine to spin cast Babbitt. I am looking for a good source for a VFD and motor.
I am thinking a 3hp would be all I would need power wise. Top speed I need to spin would be around 1700rpm.
I see some used TSUDAKOMA rotary tables for sale. Can I do the complete install myself?
Do I need Doosan to come in an step up some parameters? What about Renishaw probing macros for 4axis?
Thanks
Lonnie
We are using a probe cycle to measure a machined flat on a round part and it stores the angle from the x axis in variable #139 and the error in #144. The part is held in a 3 jaw chuck mounted flat on table. Machine is a DNM5700. Since the measurement is from zero degrees the error and the...
We have a MV1200S that we are struggling with.
When we try to do a wire pickup using type 3 for accuracy the machine will contact and then just sit there feeding wire and never moving. On a bore pickup up it make take the first 2 and then stop on 3rd and next time stop on the first.
We are...
Does anyone know a good source for reamers with a larger than standard end chamfer?
Or possibly any other tools to produce the below image. I am from holes for some lee plugs and want to create the 45 deg at bottom of hole. I am tempted to try a 90 deg carbide spot drill. Just not sure...
Looks like more fusion packaging changes are coming.
Updates to the Fusion 360 Manufacture Workspace and the Machining Extension | Fusion 360 | Autodesk Knowledge Network
Hello,
I know this is WAY OT. Does anyone know of a good resourse or forum that could help me diagnose a backfire on a CRF250R?
I tried the thumper talk forum but never got a response.
This is a backfire under load or acceleration NOT deceleration. It works fine at idling along. Once you...
I have a HAAS SL30 with a 12" Samchully hydraulic chuck.
I want to change it over to a 4 jaw. We mainly manufacture split parts and must center the split line in the chuck before turning.
The back of the Samchully chuck does not have an A2-6 taper. It has a flat back and uses an adapter...
When using a G68 to rotate the coordinate system do I need to cancel it before changing work planes (G17,G18,G19)?
I assumed I need to call out the work plane before the rotation command so we know what axis to rotate around but then once the rotation is set I could call up other work planes...
Hello,
I have a Lincoln 256. I run it on 208 single phase. I have had it for about 3 years. We use it very rarely, as in still on original spool of wire.
We have 3 phase a the shop and have had several issues this summer with dropping a single phase of power. I am not sure if this is what...
I have a round part held in a 3 jaw vise on a mill. I would like to probe and rest center at the start of each part cycle. Our cam software can easily handle the correct probe cycle but I am curious if there are parameters or some where I can look to see the difference between each part...
I am starting to look for a lathe to replace my HAAS 2008 SL30.
I currently have a price from HAAS for an ST35 and Doosan for a GT3100.
I wanted to get a quote from DMG MORI on a CLX450 or CLX550 but never heard back from them.
I have a call into Mazak on a QT250 - QT350
I am also waiting on...
Why do people seem to prefer G92 programming vs G54 on wire edm?
Or maybe they don't. The tech that installed ours used and and a couple of local shop do as well. We purchased bobcad wire software and they default to G92 as well.
anyone know is there is a setting to change between posting subroutines in bobcad V32 wire software?
We are looking to stop using the G22 HXX commands.
I recentely purchased an MV1200 mits wire edm. It has a 2D cam software in the control.
do most people program at the machine for wire or use cam software?
what software would you recommend?
I would be looking for the budget friendly software :)
I was considering smartCAM since I already...
I was wondering if someone could share how the wired the power supply on a their Wire EDM.
The mits 1200 we bought has a power supply on wheels so it can be moved out of the way. They said it would run on a 50amp circut. I have a 50amp breaker and some #8THHN I was planning to use. THHN is...
Anyone have some experience with the MV1200 S from Mitsubishi?
Are the liner shaft motors all they claim to be?
Maintenance issues?
F800 touch screen control?
Remote360 monitoring software?
I am looking into purchasing our first wire machine and have been looking at Makino and Mits
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.