Could it be that your turret may be between positions? I've had experience with my turret being in-between positions. I'm not sure about the best method for your nak if it is. My lathe I am able to force the turret clamping solenoid off, force the unclamping solenoid on through the i/o...
That is interesting. Mine went from running well with few turret indexing problems to half the time not quite being far enough. I adjusted the reluctor collar which the Hall Effect sensors read and it became better at indexing one tool at a time. There is a little movement when the turret is...
I don't think the scoring on the valve is wear. I think it's poor machining and not the problem. After a little more inspection I realized the area that looks bad does not come into contact with any of the rest of the assembly and the wear would not be radial. The part of the spool valve that...
When I purchased my Mori Sl1h centroid converted lathe the owner mentioned that the 500 watt 50 ohm brake resistor may not be the most ideal. Decel time on the Yaskawa v1000 vfd is set around 3 seconds if I remember correctly. I have tried shorter times and the vfd is not happy so back to 3s it...
I may make a spool this weekend to see if it will get me by. I'll make a trip to the Hydraulic shop this week and see what they have to say. I was expecting it to be a some what common part so I am glad to hear you think it will be. Thank you for your response!
I have also adjusted the reluctor collar and this has made it so I can at least change tools making the command of a tool or 2 at a time. I see no pattern of shared hall effect sensors on the tools that do not index properly. Although tool 2 indexes too far every time if I index from tool 3 to...
Really, only pulled it apart and found that scoring on one side of the spool valve. The other side is in perfect shape. Along with indexing problems I can see on the machine diagnostic i/o display that the turret will seem to be clamped visually but the Hall Effect sensor isn't reading it as...
Ok shrunk down some photos to fit. If needed I can pull it again there are 3 letters cast into the other side of the valve body. I am hoping I can get away with replacing just the valve. Any thoughts? The solenoid coils are p/n 02-101731
I have had a Mori SL1H with Centroid conversion for a few years. It's been a rock solid machine. And I rather like the Centroid conversion. My turret had been a little strange from time to time but it was so seldom it was not a big problem. All of a sudden I can't rely on it to make a tool...
Solid advice. I only have a couple seconds to hit the e-stop before it trips a breaker at the panel. This is the only reason I have not done this test. Great advise. Thanks!
Thanks! PM sent!
I initially made an assumption about the sound. Part of the reason was because the problem initially was intermittent and stopped with the e-stop and returned with the "hyd/lube" button.
The sound is absolutely coming from both servos. Again there were a few times that the...
I have a motor contactor on order and believe due to the pitting in the points this will hopefully be the solution to my problem. In the interim maybe someone knows where I can find an electrical schematic? TIA!!!
Hello all I am working through a problem with my 78/79 Hitachi Seiki 3ne-300 with Fanuc 6t control. In the beginning the problem began about an hour into the day and would persist. The following morning would go the same way. At first I thought sound may be caused by hydraulic pump cavitation. I...
That is helpful! I am pretty well still at the beginning of my journey with the 5t. The early version of some of the CAN cycles, using G50 and other formatting is a bit of a curve. I feel like I've spent the entire summer getting the machine going and getting up to speed. But it has been a good...
I edited the forceDecimal out. I think I like the idea of out puting g code with decimals and then using note/word pad to edit them out. This has been pretty easy so far. That way I can check over some of the moves more easily while there are decimals. I've been tied up with power outages and...
Gotcha! Either my implementation of where is goes in the code is no good or it does not like having the field empty. That's ok. I can edit out the decimal with word/note pad I believe. This is obviously my first round with JavaScript lol...
I just searched the post using the search option in word pad for '.' and came up with no such characters in the post. But I found where it says just that in the training guide.
I actually was unaware of any such material until I found the following link this morning.
https://cam.autodesk.com/posts/posts/guides/Post%20Processor%20Training%20Guide.pdf
Thanks for taking the time to make the suggestion!
I posted in a few places looking for help with this to no avail. I am going to try and update those threads for anyone this may help. Hopefully this is correct it seems to work as intended in preliminary tests
Ok so I have finally figured out how to assure that trailing Zeros are not...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.