What's new
What's new
By:
Advanced search…

Search results

  1. H

    Help is needed Mazak cam M2

    I posted Clearing the 22 alarm instructions and the parameter pictures here to help others in the future.
  2. H

    Help is needed Mazak cam M2

    Last 2 pages
  3. H

    Help is needed Mazak cam M2

    Why post screen shots when I have the book First 2 pages
  4. H

    Help is needed Mazak cam M2

    Do you know how to view and edit the Machine parameters?
  5. H

    Help is needed Mazak cam M2

    Clearing the 22 alarm: On the FX1 / FX701 Card It is best to pull it out to work on it. There is an 8 position switch under a cover. The top and bottom switches are off. If you are not able to flip switch next to the top one, there is a lock assembly that locks the back of the switches. I had...
  6. H

    Help is needed Mazak cam M2

    In post #1 you show a screen with a 22 alarm. What is the English wording for that alarm? The 22 alarms I was working with there were pe lights on 2 boards in the card stack. Yours are off.
  7. H

    408 program error on V10 with M-2 control.

    I have replaced the 3 batteries in the control then bringing it back from brain dead. I have resolved the remaining alarms and have only the "408 Program error" left. Any info on clearing this alarm will be helpful.
  8. H

    Help is needed Mazak cam M2

    I just finished a V10 with the M-2 control.here in the USA. Changed the batteries and Super caps on 3 boards. Then brought it back from brain dead. Post a picture of the front of the control showing the alarm LED's. Mid next week I will be back in that shop, and will pick up the procedure to...
  9. H

    Help needed in finding a copy or scan of Hardinge UDD-8220 schematic for DV or DSM 59 Lathe

    I am chasing gremlins around my DSM-59. I only have a schematic from a much older (mid 60's vintage) machine. At some point the spindle motor was rewound for 230 Volt operation. I don't think the overloads and things were ever changed from 440 Volt operation. The door lists the schematic as...
  10. H

    Monarch EE: Oh no, not the single phase question again...

    This is a conversion I worked on 6 or so years ago Full documentation is included for those that want to duplicate this setup. 43 10ee MG with Parker 514c-16 DC Controller
  11. H

    Hardinge HC spindle variable speed won't change speed troubleshooting info

    Here's the pdf link on Babinmachine.com if anyone needs it: http://www.babinmachine.com/PDF/Hardinge HC maintenance manual, new style.pdf
  12. H

    43 10ee MG with Parker 514c-16 DC Controller

    I check in with Rob, Everything is working flawlessly 6 years later. Bill
  13. H

    10EE KB 255D drive problems; Parker 514/507 conversion questions

    What is the resistance of the field rheostat?
  14. H

    10EE KB 255D drive problems; Parker 514/507 conversion questions

    I was going to let him answer some of the questions first. The vagueness quoted below needs to be ironed out. "On a good day, going downhill, with the wind to my back, I can get 1,250 rpm. So says the dial tach. I forget it’s been a while, but I think the field winding is running though the...
  15. H

    10EE KB 255D drive problems; Parker 514/507 conversion questions

    Hi, Cal has asked me to jump in. Many questions need to be answered. Do you really have 208 Volt power? What is the motor field voltage at max RPM? Is your Tach. reading correctly, many read low, some very low. What is the pulley size on the motor and spindle? This is a retrofit I did some...
  16. H

    Hardinge HC spindle variable speed won't change speed troubleshooting info

    Scott. Just click on the view attachment links, or go to the first post in this thread, you can view or print what you want. also see my Nov 26, 2018 post. Bill
  17. H

    QT-250MS with Smooth control, need Tool Eye alignment procedure

    Have any of the gurus here ever done a Tool Eye alignment on a QT-250MS with Smooth control. I got roped into installing a replacement and getting it calibrated. Parameters BA95 - BA99 seem to be the ones that need to be tweaked. I have only done 2 axis machines without a sub spindle, last...
  18. H

    QT28 T2 control won't go into ready state

    Make sure the spindle controller powers up properly Many of the T2 controls I have worked on have FR-SE spindle drives, and the power supply in the top do go bad.
  19. H

    Mazak QT15 Lube System Issues

    I make sure the pump is primed at it's output. then plug the pump output and lift plunger and release to pressurize. The plunger should NOT go down in a half hour or more. If it does, there are internal leaks in the pump. I have replaced a pile of pumps over the years. Bill
  20. H

    VQC 20/50A M2 drive faults

    I would do a reality check of your lube system to insure there is lots of lube on the ways. If the ways run dry, it takes more power to position (larger lag) all axis can be affected, and motion can be jerky as the breakaway friction has increased. Since you have been tweaking adjustments, and...

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top