I have replaced the 3 batteries in the control then bringing it back from brain dead.
I have resolved the remaining alarms and have only the "408 Program error" left.
Any info on clearing this alarm will be helpful.
I am chasing gremlins around my DSM-59.
I only have a schematic from a much older (mid 60's vintage) machine.
At some point the spindle motor was rewound for 230 Volt operation.
I don't think the overloads and things were ever changed from 440 Volt operation.
The door lists the schematic as...
Have any of the gurus here ever done a Tool Eye alignment on a
QT-250MS with Smooth control.
I got roped into installing a replacement and getting it calibrated.
Parameters BA95 - BA99 seem to be the ones that need to be tweaked.
I have only done 2 axis machines without a sub spindle, last...
I am starting to part out a 1985 Mori MV-JR.
Control is a Fanuc 10M Main board P/N A16B-1010-0040/070
Servos are Fanuc Yellow cap DC.
Spindle bearings got noisy and decided to part it out.
PM me with any requests,
Bill
I am looking for a set of schematics for a Hardinge AHC.
The set is KHB-8220.
If anyone has a set, how many pages are in the set?
Has anyone found a set of scans online?
There are 50 or more relays and a half dozen timers in the electrical panel.
It will be a bit much to bring it back to life...
Hardinge HC troubleshooting info for variable speed change problems
Over the years several people have had problems with the HC variable speed unit that will not change speed properly.
The main problem starts with the electrical drawings are never with the machines and appear to be hard to...
I am trying to remove the cross slide from a 1937 Hendey 14 X 54 18 speed.
It has the quick retract option and some parts from a TA still there that seem to function more like a cross slide lock.
I suspect that there is a screw or two covered in crud that are key to taking this apart.
There...
I have never made any sense of the various "charts" for metric transposing for the single tumbler.
Hole #6 seems to be the problem.
So I have sketched a setup based on the TPI pitch to set the box to, to eliminate confusion.
For common pitches I need 5 stud gears, the transposer of 127/100...
I am working with a small shop that was in the process of purchasing a pair of running Mazak VQC-15/40 mills. That was until the ham fisted maint guy started riping the first machine apart suitable for scrapping, not to be put back in service.
The deal is still on at this time.
Most parts for...
I was looking for something else on ebay and ran across this:
http://www.ebay.com/itm/ANTIQUE-Hand-Operated-Metal-PLANER-EARLY-industrial-Revolution-Small-MODEL-TOOL-/220905497102?pt=LH_DefaultDomain_0&hash=item336efe620e
It's just a short trip, from most anywhere, to CLEVELAND,OHIO. to pick...
Is anyone familiar with the connection needed to run a 4 lead, 2 phase, 240 Volt, 90° phase shift motor on 3 phase, using only 2 transformers?
I understand eastern Long Island power was 2 phase in the past, and was converted to 3 phase when needed.
I suspect that if one has 120/240 Volt wild...
Hi,
This is my first new thread, hopefully I can upload pictures.
This nice planer was in a local used machine dealer office 50 years ago. I purchased it when they liquidated the firm after the owner passed away.
I have found out that is a very early Hendey probably from 1870. It is the...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.