A long story shortened, 2008 Agie Classic S. Hard drive failed. Replaced and software reloaded [as far as I know]. Everything seems to be working with these exceptions, yet to make sparks with it. Problem with the wire tension/feed is new, was working before hard drive failure. The tank fill /...
2007 SL 10.
New to me, and has very low hours, consider it new! Seriously - I don't think it has ten hours of spindle on time. It is that clean, I need to look but trust me - its mint!
We came by this machine when the owner lightly crashed it and decided there is more to machining than he...
Just thought to share - 2007 Mini Mill.
At my paying workplace for some time when homing on the Z axis there was a loud clunk. Since we run a *RTR maintenance program and their were no other issues I ignored it. Fast forward a over a year later and the machine is suffering a slow tool release...
ProX 200
Interested in hearing from any users of this early entry by 3D Systems to this 'Very French' machine.
I am looking to share experience, maintenance and repair that you have done.
I have an awsome LED light modification and replacement quick connect hose clamping that can be used...
We are installing a new to us 2005 AGIE Classic wire EDM machine.
I have the OEM DI resin tank but no resin.
It has been suggested to simply buy a replaceable cartridge system in place of the OEM tank.
I am reading of bulk resin that can be regenerated and supposed lower operating cost.
Is...
Mobil 1 5w30 for use as way lubricant.
This has been discussed in another post sort of. The corporate promotional conspiracies aside.
For my Berta, shes a '92 VF-O, I have made the changeover.
I removed the tank and the fine filter assembly. Poured out the remaining oil to find a palm sized...
I am about to jump in the deep end [for me] of the pool of EDM. We have a 2007 ONA DB 300 that has not had the cosmoline removed nor the power switch thrown on since taken out of the crate upon delivery in early 2008. Safe to presume the warranty is past due so no worry there..
I have been...
Located in Mt Vernon, VA - Location Pickup only!
Serial # 452-872-70
• All manual table feed and motion
• MD-5 spindle, 1hp, 230-460 VAC 3phase 3450 rpm
• Automatic multipoint lubrication
Selling complete only with the following:
• Rocheleau air bearing end mill sharpening fixture and...
At my day job our 2004 Mini Mill - tool shuttle motor died in 2008, mind you that this machine saw intermittent use, I don’t think it saw more than 200 hours of use total by then. The design with its compact size and necessary plastic cover I suspected coolant infiltration. At that time the...
I have several of these from NOGA deburring kits. I find them all the time abandoned in the back of tool boxes, the only thing left in an all but empty kit or in boxes of junk, etc. Can anyone show what the heck it is for or how to use it. No guessing - it is clearly a quality piece, it must...
My 1992 VF0, is there a way to copy all the parameters as a file to an external memory. I took digital pictures of all the pages on the monitor but I was hoping I can down/up load it like a program file. This is just as a backup in case of a major failure in the control.
NIST - the National Institute of Standards and Technology is in my home town of Gaithersburg MD. There is a position for a engineering tech that I am interested in.
Ironically because of the current "issue" the offices are closed and there is no one to answer my calls or e-mail.
If one of you...
My question is to experienced CNC programmers. I'm self taught in FeatureCam, I can get along ok but there is a lot I'm missing and to be honest I spend too much time editing and revising all but the simplest programs. Not to be stuck on this particular software my question is for any job on any...
Our shop has inherited a 1956 10EE with the DC motor generator drive, Ward Leonard Drive System I believe its called, machine is in excellent shape, but will not go above 200RPM in either direction without the motor switching off/on off/on. below 200RPM it runs fine; The "switch" I am speaking...
I have been tasked with getting a 1956 vintage 10EE back in service. A pleasure really, what a beauty, other than dirty and neglected I have it in working order thanks to the wealth of information posted here. One thing I'm stuck on is the horizontal bar shown in the picture here, I believe it...
So last episode we lost the vector drive on my1992 VF-0, yea last post I said it was 1997, to late to fix it then. In any case, we sent the unit out had it repaired and reinstalled it, seems fine, start/stop, M03/M04, orient - seems fine!
I Ran the long warm up routine, takes 30 min to get to...
Hello, got the old girl all ready to dance but coolant tank and pump running. After doing a spindle warm up I tried a tool change with the MDI, I get a 149 Spindle turning alarm, cycled tool in/out manually, works fine. Rebooted and power up/restart; no better, did hear the solenoids tripping...
Optical tooling - auto collimation to mirror cube
Two Questions:
1) Can I use a precision mirror to auto collimate to a corner cube 90 degrees to the cube face?
We are in a situation where we cannot be in direct line (perpendicular) to a corner cube. We have a precision 2” diameter mirror that...
Hey kids,
Got all the work done on my 1992 VF-0 and am starting to put back all the covers we had to hastily remove for transport.:willy_nilly: Have some parts we are wondering where they go. Its the early cartoon version plastic type, I was hoping someone out there had one and would be kind...
Q: What amount of mechanical backlash is acceptable?
Almost ready to start making chips with "this old Haas" my 1992 VF0 restoration project. While indicating the vice I decided to check the backlash on all axis. Comparing display to dial indicator the X and Y are better then 0.0005", I can get...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.