I have a mint 1903A3 Springfield with receiver marked Nat Ord.
What do I have? I know that they were made by several different armories, but I never heard of Nat Ord.
The serial number is in the 50023XX range. The barrel is stamped RA and dated 5-44 .
Any help is towards value and...
I just acquired another datsun forklift and I need to install a step to make it up into the seat. With age problems and bad knees, am finding it ain't easy to step up 24 1/2". Any suggestions? Considered installing a 4" x 6" plate step 12" high. Should I make it to fold up when not needed?
JC
Like the title says, on my old Datsun/Nissan, the forks will go up just fine, but when going down, thay stop about 9 or 10 inches from the floor.
Anybody run into this before? I think its hydraulic, but don't know where.
OT: Anybody got an opinion on the Boxer 6 engine in the new Subaru Legacy's? We have a 2015 Legacy with V6 that we really like. Wanting to trade for new Legacy, but V6 no longer available. What is everyone's opinion on the new engine?
JH
Got a small 3000 lb. fork lift that has began to stop about a foot off the floor when letting the forks down. Can't get it to go lower, but by setting for a few days, forks will slowly go down by themselves. It sounds like a hydraulic problem, but not sure where to look. Has anyone run into this...
I have been having problems ,like TDegenhart, with the Private Message system. When I try to use it, as soon as I am ready to send, then suddenly I am unlogged in.
JH
On Edit: I emptied out a bunch of old P.M.s, maybe that will help.
JH
Does anyone have a preference for one or the other when comparing Weaver brand toolkits to Wheeler? I have a lot of machinist and auto/truck tools, but thinking about buying some tools for my own use at the house for my own guns. Tired of bringing up tools for the occasion when doing a little...
I have an old (1970's) 3 ton Datsun/Nissan forklift that starts and run poorly. It will start and run as long as the accelerator pedal is pushed, but does not want to idle. I suspect fuel problems, but not sure. I worked years ago (50) as a auto and truck mechanic before I started my...
Is anyone else having trouble staying logged on? I tried to contact Practicalman, but don't think it went thru. So far in the last thirty minutes, about 6 or 7 times. Every time I change forums or try to launch a P.M., bingo, I'm gone.
JH
FS: KBC Bandsaw w/20" throat, blade welder, 220V, single phase
Excellent condition, Still under power. Several boxes extra saw stock.
$3000.00 or best offer.
E-mail - [email protected]
or P.M.
pics to follow if possible.
O.T. Can surge protectors such as the kind we use on the back of the computer desk that have multiple outlets, lose the "surge protection effectiveness"? I was told this by computer techs at Best Buy and other stores. Supposedly, they will still function as electrical outlets as normal. If so...
I'm helping a friend build a phase converter with a Dayton Tri-Volt TEFC motor. It runs at 1745 RPM and the model number is 3N734. It runs good when wired up with two legs on 240V single phase and spun up with a rope. We were trying to get it to start on some capacitors and it trys to run at a...
I'm helping a friend build a phase converter with a 7.5 HP Dayton Trivolt TEFC motor. this motor runs at 1745 RPM and starts easy with two legs wired to 240 single phase and spun with a rope. It is usable with 208 or 240 or 460 volts. It is presently configured for low voltage. When we put...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.