Davidson D-600 autocollimator - Can someone help with a question?
Hello All,
I just purchased a Davidson D-600 autocollimator. Would someone with specific knowledge of this unit, be willing to answer a few questions for me?
JB
Hi All,
I am putting together a hydraulic circuit and being an amateur at hydraulic I have a few questions.
There is only one double acting cylinder in the system. My goal is to be able to extend or contract the cylinder and locking it in place when the directional control valve is put in...
Jst and all thanks for the advice. Jst if I were to get a 45kva 3 phase transformer is it possible to only use 2 of the legs so I could do single phase 220 in and the 440 out so I could build another rpc to run the 40 hp idler?
Hi all,
In a previous post I asked about the best way to use my current 220v 10hp rpc to run my 20hp 460v lathe. One of the suggestions was to get a larger motor and make it into an rpc. Today I came across a reasonable deal on a baldor 40 hp 3 phase motor. As a side note I later found out it...
I bought a Leblond lathe and would like to change the oil in the head. The placard calls for 20w - 20 motor oil. I am finding it difficult to find locally and the oil I find online is a bit expensive. The lathe is a 1976, I am wondering if oil technology has changed and there is a better oil...
Hello All,
A few years ago I built a 220 volt 10 hp rotary phase converter based off of Bruce Norton's design. I figured that I would never need more than 10 hp. Well! I bought a Leblond 20 SL lathe that has a 2 speed 10/20 hp 460 volt motor. I do not not see that it is possible to re-wire...
Hello All,
I just got a phone call from an acquaintance of an acquaintance or in other words someone I don't know. :) Anyway he has a 3 year old supposedly in good working order, hyper-therm powermax 85 he has offered to sell me for $2000. It is suppose to have the cnc card in it but it has...
In addition to the above questions about balancing. Why is it that when measuring voltage
From common to L1 and L2 I get 122 volts each but when between L1 and L2 I only get 210? Shouldn't I be getting 244?
Hi all,
I just "finished" my 10 hp rpc. I am trying to balance the legs and I clearly am doing something wrong. The idle motor has a max amp of 26. My L1 - L2 are 209 volts. So far I have bc at 233v ab at 232v AC at 208v no matter what what capacitance I add to the CPf
It won't change the...
Hello All,
I have a 10hp RPC that I want to distribute to 3 machines and one socket, for various small 3 phase equipment. The machines are on the opposite side of the shop from the breaker panel. My thought was to mount, up on the wall, the RPC within 5 ft of the breaker box and use #10 wire...
crrmeyer, As of this date I have not located a manual for the unit. I really hate to have you spend that much time scanning. That said, should you decided to do it, I will be sure to follow your pay it forward approach when the opportunity arises.
Happy Holidays everyone!
I just picked up a BP that has a MITUTOYO GML-3705 DRO installed. I am really surprised that with the amount of searching I have done I can not locate a manual for this. Does anyone have a pdf or copy of a users manual.
Hello All, I didn't see a Logan specific forum so I hope it is ok that I am posting here instead. I just bought an old dirty Logan 922 lathe. The lathe looked fantastic while sitting in the dark corner of the guys garage. Once I made the deal and saw it in the light of course there are some...
Thanks all, what I did was took my ohm meter and lightly ran the probe down each strand and then separated it out of the group. The chuck is now working but I am not sure if it is working at it's highest potential holding capability. Should I decide to pull the whole coil out and respray the...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.