QT: (The workers on the shop floor blame management, management blames the rank and file, but no doubt most everyone at Boeing is part of the mess.)
and I think legal weed id a factor.
People not putting in the bolts, not making them tight is a difficult problem to design away.
We really need to give everybody all of our money, so when we are flat busted we can ask for help.
If we would invite all the terrorists to the USA then the rest or the world might be safer.
I’m not the lathe guy, but if losing productivity with tool failure I would cut my feed rate or chip load 20% or something
7" out unsupported might need tail support..
You might angle dress a wheel 45* or 60* with the straight wheel side toward you drill center about .005 short of center. come to the part (drill) at a height the would make the split gash about 1/6 to 1/8 wide depending on the drill size. Dressing the angle as its radius become too big. the...
QT: (Iran is run by a bunch of nutjob fanatics .......the one thing stopping them from an all out attack is the probability of being roasted to a crispy crisp).
And they like free momey as a bribe to be a little bit nice.
I have not split drills on a Monoset, and I don’t have one here to experiment.
The split grind does not go way toward the the OD as you have tried.
look at I and J. -> the split thinning is not very wide.
QT : The conventional split point (CSP) is highly productive but is limited since it...
Another thing with electro plated wheels.
If you mount them indicated-in or dressed-in it is good to keep them on the original mount, and mark a line-up mark so they can go back on the spindle at the same 180/360(same place on a circle.)
At mounting good to indicate to <.001 if you can..*(that...
Another thing with electro plated wheels.
If you mount them indicated-in or dressed-in it is good to keep them on the original mount, and mark a line-up mark so they can go back on the spindle at the same 180/360(same place on a circle.)
QT: I want:
Variable speed
At least 3 hp
2000 rpm or greater
12x40
flood coolant
DRO
-DROs are great, but to be a good lathe hand a student should learn/practice runnimg a part with hand measuring tools also, learn to mark to +- .oo5, measure an OD and take the proper amount using dial numbers...
qt: rklopp: Weiler, Sharp, Kent, Acra Turn, and Acer..
ad Harrison
A great list with a 3jaw/4jaw /steady and a taper attachment.
If having a DRO have students run it also with not using the DRO.
Have students know how to come into pick up an existing thread, how to design a special thread. How...
Photo doesn’t look that good, might just be the photo.
The split gash is just a small gash usually done with a harder wheel.
Here find some points to shoot for...
QT: the guy who leaked the documents was just another young fruitcake wanting to...
It really seems odd that pool guy has the combination to the owners safe in the military and important places, in retrospect.
QT; Why the passive aggressive comment?
Passive aggressive? Centanily not intended to be that.
I asked what RPM, turning that shaft at 3600 needs a whole lot more thinking.
QT (Thanks again to everyone for your help and input; I gather the best route to go down is a brand new 40mm shaft from hardened steel, and another pillow block bearing)
No, the best rout is to tell what needs to be done and designe a something that can do the task.
Gussing from here you may...
600mm 24 inch even in wood is a big dangerous part, likely you should have a machie of 1000 pounds or more for lathe turning a part that big..
There are safer ways to round and shape a part that big. Some times a big part turning slow and perhaps a cutter turning fast can be safer.
The guys here...
For your own in house cutters most often altering a standard citter is best.
Sharpening an end often you can facet grind the secondary and then butter fly (just go in and out) as you roll the heal up into the wheel..Yes watch out for the under tooth/edge.
likely somone told you the 1/2 distance to the one bearing. and then the full distance out what error you have at the motor will be double at the far end.
If you put on two bearings then the shaft will/may run true and you may have a big vibration where there is error at joining the motor.
QT...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.