i have several of these (i like them) but one that i was gifted is very old and it is venier, not solid oak. does anyone know the history of these; or, is it a cheaper model??
i need a thickness planer for a small amount of wood. i see that home depot advertises a dewalt 13 in thickness planer for $69.00 . am i missing something or is this a mistake??
at this time i amusing a grizzly wall mounted 1 HP dust collector. never did like it. what are the thoughts of a Festool dust collector. they look like a large shop vac. i will be using it for a 6 in belt sander and a 14 in bandsaw. suggestions/ advise??
i have apiece of cherry board 3/4 thick 7 in. wide and 6 ft long. it is cupped (i think that is what is called) anyway, it has a dip in the wood running lengthwise. at the lowest point, running the whole length it is about 3/16 in. is there a way to correct this??
i've always sharpened planer blades and chisles by hand. jusd ordered a honing guide. this will work much better, i'm sure. but, is there a better way to sharpen gouges and curved chisles that by hand??
i think that odies oil is good stuff. however i'm tired of it turning to chunky jelly in a short time. the last that i bought ; i poured into 3/4 oz glass bottles, thinking that will stop the jelling process. (i don't mind the jelling, but, it gets big chunks also) the small bottles also got...
asked this question on another site also. a friend worked as a tool & die maker in a shop where they used south bend lathes. he said that they used only 2 lubricants on the lathes. my guess is that one is the designated spindel oil, the other ?? what would the other lube? since the technology...
bought a older gerstner "dental tool kit" box that is leatherette covered. in poor shape. i removed the leatherette and it is mostly covered with residual glue. the box under the covering is plywood and finegrain partical board. . after sanding well, i want to use a primer that has a "filling"...
need a piece of 3/16 cold roll plate 6.5 x15 inches. can't locate anyone. i know there are companies out there; but, i guess i missed them. i want it to cover the recess worn into the platen on my belt sander. any help with getting it cut to size??
my 6x48 belt sander has a .016-.018 dip in the center. i was thinking that i could use turcite to "level" it. my thoughts are to spread the turcite epoxy around; then cover it with wax paper. then lay my granite surface plate over it to flatten the epoxy . never used turcite before; any...
anybody ever tried or use it. a have a bottle of Mahoneys walnut oil. have a "practice piece" of crabapple that i am soaking it into. never stops soaking in. rubbed a little on a piece of steel and left it under the furnace register overnight. still wet. put a small amount in a bottle cap and...
i have many pieces of high grain (crabapple) about the size of a very large hand. i will put them on a base and gift them to friends. the best finish, i belive would be a pure wax finish. never done that. looking for some guidence in the process of doing so??
i'll try to keep this short. tried a new motor. new 3/4 horse 3 phase using a vfd. still can stop chuck with my hand (very easy). a machinist told me that he thinks that ; with a VFD that i need a phase convertor and a bigger motor. everything has been fine for almost ten years without a...
i have pieces of crabapple and yew 2-6 inches in diameter and up to 18 inches long. after sealing the ends; i wonder if i store them in my shed where it is probably 120 degrees today. if, this would accelarate the seasoning. i'm very impatient about the seasoning time required. each 1 inch of...
i have a 4 1/2 in prentiss vice that i can't seem to find info and value on. it is a bulldog new york. one cast logo is 525 on a oval. the other logo is 515 over 525 in a circle. nothing that i can find has those three numbers. they sure did make a lot of vices at one time!
i have a 14 in bandsaw. having trouble cutting with the 3/8 - 6 tooth blade. the wood is apple sections 10-15 in long; 6-8 in diameter. going to order a new 1/2 in blade. what should i get. hook or skip tooth? 3 or 4 tooth??
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.