What's new
What's new
By:
Advanced search…

Search results

  1. C

    Alarm 2064 during tool change

    That could very well be it. Anyone have any ideas how to clear the error so I can zero everything? I was able to retract the ATC but can't move the Z to unclamp the tool until I clear the alarm.
  2. C

    Alarm 2064 during tool change

    Hello, I have a new to me MYNX 500 Fanuc 21M control with the umbrella ATC. I have been able to dry run tool changes but when I tried with an actual tool holder I got a 2064 WAITING TOOL POT SPINDLE/MAGAZINE SIDE ALARM & MAGAZINE POSITION ALARM. I was able to manually retract the ATC but have...
  3. C

    Hardinge VMC1000II Tool Changer adjustment

    This worked perfectly. I was able to jog the umbrella back and forth with M72 and M71 to make the adjustments. It ran out of adjustment before getting perfectly in-line with the spindle but it is much better and the tools are close to being fully seated in the changer. Thanks for your help!
  4. C

    Hardinge VMC1000II Tool Changer adjustment

    Sweet. I will try this out on Monday and let you know. Does yours have the same umbrella style changer?
  5. C

    Hardinge VMC1000II Tool Changer adjustment

    Here is the tool change macro. I have tried piecing something together referencing it but I am still too green to know what is needed. :9020(TOOL CHANGE SUB-PROGRAM) IF[#1014GE1]GOTO10 IF[#1015EQ1]GOTO20 IF[#20EQ0]GOTO30 #1100=1 G91G30Z0M19 M76 #106=BIN[#1032] IF[#106EQ#20]GOTO40...
  6. C

    Hardinge VMC1000II Tool Changer adjustment

    Anyone have any ideas? The manual says M72 extends the tool changer and M71 homes it but punching in M72; in MDI does nothing.
  7. C

    Hardinge VMC1000II Tool Changer adjustment

    I am having a couple issues with my umbrella style tool changer. The umbrella is not extending far enough to align with the spindle. The tools are just barely being held by the tool holders. There is a mechanical adjustment on the tool changer slide but I don't know how to force the tool...
  8. C

    Hardinge VMC1000ii and Fusion 360 issues

    I will make those changes and see how it goes. Thanks for your help!
  9. C

    Hardinge VMC1000ii and Fusion 360 issues

    Is this how you were thinking it should be? Thanks again guys for all your help. :9020(TOOL CHANGE SUB-PROGRAM) IF[#1014GE1]GOTO10 IF[#1015EQ1]GOTO20 IF[#20EQ0]GOTO30 #1100=1 #101=#4001 (STORE INTERPOLATION MODE) #102=#4002 (STORE PLANE SELECTION) #103=#4003 (STORE ABSOLUTE OR INCREMENTAL)...
  10. C

    Hardinge VMC1000ii and Fusion 360 issues

    Yeah looks like he nailed it. I took the tool change completely out and it seems to be working correctly now. What would you guys suggest I do to cleanly resolve the macro?
  11. C

    Hardinge VMC1000ii and Fusion 360 issues

    Added a G90 following the tool change and now I'm getting a 224 P/S Alarm on line N55. N30 T5 M06 N35 S2140 M03 N40 G54 N45 M08 N55 G00 X-0.0491 Y-2.3205
  12. C

    Hardinge VMC1000ii and Fusion 360 issues

    Here is the tool change :9020(TOOL CHANGE SUB-PROGRAM) IF[#1014GE1]GOTO10 IF[#1015EQ1]GOTO20 IF[#20EQ0]GOTO30 #1100=1 G91G30Z0M19 M76 #106=BIN[#1032] IF[#106EQ#20]GOTO40 #101=#4001 #102=#4002 #103=#4003 #104=#4015 G17G91G80G00G63M75 G30Z0.M19 M72 M74 M17 G28Z0. T#20 M17 G30Z0. M73...
  13. C

    Hardinge VMC1000ii and Fusion 360 issues

    That is a very real possibility as the previous owner knew less than I do and that's not much. Let me pull the macro and have a look. It also isn't pulling tool 5...
  14. C

    Hardinge VMC1000ii and Fusion 360 issues

    O1225 (SCDC TEST) (T5 D=0.5 CR=0. - ZMIN=-0.75 - FLAT END MILL) N10 G90 G94 G17 G49 G40 G80 N15 G20 N20 G28 G91 Z0. N25 G90 That's what Fusion output.
  15. C

    Hardinge VMC1000ii and Fusion 360 issues

    Correct. Table is towards you and to the right as looking at it when homed.
  16. C

    Hardinge VMC1000ii and Fusion 360 issues

    Depends on where the table is when I start the program but I have had it over-travel in X and Y.
  17. C

    Hardinge VMC1000ii and Fusion 360 issues

    Thanks, will post it there. For G54 Z= -18.982 X= 17.8602 Y= -7.3490 These are all based off of the machine zero.
  18. C

    Hardinge VMC1000ii and Fusion 360 issues

    Hi, I am looking for some help with a new to me 2000 Hardinge and getting Fusion 360 CAM to work together. I am trying to do a simple part as shown below but I am running into problems with the CAM sending my machine into over-travel. I am not sure why it is telling the table to move in 2 inch...
  19. C

    Uneven lathe material removal

    Yeah you sure called it! I won't lie, I puckered a bit after the dry pass when I saw just how fast it was going to be ripping across it. Thanks again man.
  20. C

    Uneven lathe material removal

    Just couldn't wait until morning. Made a few passes at 1150 RPM .0078" feed and took .120 off of the diameter which left a consistent finish and littered the garage with perfect beautiful little blue chips. The photo really doesn't do it justice. I should mention that I also went back and...

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top