Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Largest Manufacturing Technology Community on the Web
Stay Connected:
Search results
-
H
10mm 82* countersinks. Where can I find these?
Where can I find such a beast?- Houndogforever
- Thread
- Replies: 1
- Forum: CNC Machining
-
H
Swapping out 4th axis on Brother
https://www.yamazen.com/tooling/monthly-promotions- Houndogforever
- Post #5
- Forum: CNC Machining
-
H
Swapping out 4th axis on Brother
You could buy a new brother T200-A for about $13k. What budget are you looking at?- Houndogforever
- Post #3
- Forum: CNC Machining
-
H
Tool Recommendations wanted for small high feed mill in 316
Also I think HFM cutters don't leave the best face finish, so even after blowing off that .040, you will still need to finish face it unless you are allowed a rough finish on the face.- Houndogforever
- Post #9
- Forum: CNC Machining
-
H
CNC of Chinese origin
It depends on what you want the machine to do. Do you have a small part that just needs a small modification, well it may be fine for that. I know I have an entire product line that could be run on a SYIL 5 if I wanted. Do you want it to be a full spectrum cnc. It won't. Parts life is...- Houndogforever
- Post #5
- Forum: CNC Machining
-
H
For those in PNW/PDX . . . where do you take your chips?
I found out that RS Davis out in Gresham area only offered $1 per pound for used carbide. I think Metro gave me $3 at the time. It seems the closer you get to heavy rail lines, the more money they will give you for scrap.- Houndogforever
- Post #12
- Forum: CNC Machining
-
H
Drilling speeds and feeds for tool steels D2, H13, O1, S7, W2
How are you holding them? What diameters are you drilling? I'm using some Nachi SG-ESS drilling a 1.98mm hole in D2 and I'm at 35sfm and .002ipr. These are not carbide drills. Most carbide drills have recommended speeds and feeds, what brand are you using?- Houndogforever
- Post #2
- Forum: CNC Machining
-
H
Keyway "broaching" on CNC lathe with no M19 / spindle lock?
Hell my conquest 42 from 1989 has a disk brake on the head. I put a 8mm key way in a 30mm bore of 4140. Can you reach in and rotate your chuck at any time? I have a setting on mine that lets me choose either free state, or locked in position.- Houndogforever
- Post #15
- Forum: CNC Machining
-
H
How to hold a small part. 3/4 sq x 1.38 long
It is a wear part and they said they would order in quantities of 20 of each hand. There are other plants so there is an upside too.- Houndogforever
- Post #14
- Forum: CNC Machining
-
H
How to hold a small part. 3/4 sq x 1.38 long
One hole is counterbored from other side for a bolt. The smaller hole must be a locating pin. it only goes about half way thru- Houndogforever
- Post #11
- Forum: CNC Machining
-
H
How to hold a small part. 3/4 sq x 1.38 long
The part is small, but has some very thin parts. It currently seems to be machined out of tool steel and measures up about 60 HRc but the customer says that is too brittle. So I'm opting for 4140 and have it heat treated to 40-45 RHc and machine it after HT. I was thinking if I could saw bar...- Houndogforever
- Post #4
- Forum: CNC Machining
-
H
How to hold a small part. 3/4 sq x 1.38 long
I have a small part that could be made from 3/4 square bar or from 1-1/16" dia . I want to hold the bar in the 4th axis and hang the part out about 1-3/4" in order to machine 5 of the six sides. So how to hold it? Round collet with stop? Might be less secure. Round soft collet with blind...- Houndogforever
- Thread
- Replies: 14
- Forum: CNC Machining
-
H
Opinions wanted - best CNC machine for this part?
I know next to nothing, but I would think VTL would be the choice. No sag and like he says above, gravity is working for you.- Houndogforever
- Post #22
- Forum: CNC Machining
-
H
Titan is peddling Syil?
Sadly most cnc knee mills don't have a tool changer.- Houndogforever
- Post #117
- Forum: CNC Machining
-
H
Titan is peddling Syil?
That little mill surely has it's place. I have a bunch of parts that are run with a 1/4" endmill and about 4000 rpm. I am sure it would be great for little niche parts.- Houndogforever
- Post #74
- Forum: CNC Machining
-
H
Need some ideas for holding 3/4" aluminum plate for machining.
Who can jump?- Houndogforever
- Post #11
- Forum: CNC Machining
-
H
TsugamiBS32 for sale SoCal, other swiss machines, manual Hardinge lathes
Post #24 has the info you seek.- Houndogforever
- Post #36
- Forum: Machinery for Sale or Wanted