What's new
What's new
By:
Advanced search…

Search results

  1. D

    Heidenhain TNC 426 tool changer no basic position

    If the control cant find the help file than you must put in the file PLC:\OEM.SYS file the line MODEHELP = PLC:\LANGUAGE\ENGLISH\ or the path for the help files in your machine. Hope to save the frustration for the next owner of TNC426 control
  2. D

    Heidenhain TNC 426 tool changer no basic position

    I have found the solution. 1. Reboot 2. Once rebooted start the machine with ON button an CE as normal 3. Press the cycle arrow button to go to programing and editing screen 4. type the code 789 and pres enter, the code will disappear and It will seem like nothing happened. 5. press the Help...
  3. D

    Heidenhain TNC 426 tool changer no basic position

    Hi, i have a DMU50evo 1999 model with Heidenhain TNC426 control, i get the message "tool changer no basic position" and i can move anything. How i can access the tool changer diagnostics of the control. I have tried the help function but it is just a text file and it is not describing how to...
  4. D

    DMG DMU 50 Evolution machine constants

    Press save button first (1) and then the menu (2). jog with the direction keys to the far right tab ant in the bottom there is machine constants to make any change you have to enter 1234 and enter. after you can change any constant
  5. D

    DMG DMU 50 Evolution machine constants

    Rotation center of C axis X-250973 Y-156185. Top of table Z-543280. Intersection of B with C axis at point X-250973 Y-156185 Z(-543280+155170). they don't really intersect as they are 6 microns apart (N623 C6)
  6. D

    DMG DMU 50 Evolution machine constants

    N600 C2 N601 C1 N602 C1 N603 C-250973 N604 C2 N605 C2 N606 C1 N607 C-156185 N608 C2 N609 C3 N610 C1 N611 C-543280 N612 C2 N613 C6 N614 C0 N615 C0 N616 C2 N617 C3 N618 C0 N619 C155170 N620 C2 N621 C1 N622 C0 N623 C6 N624 C2 N625 C4 N626 C0 N627 C-45000 N628 C2 N629 C5 N630 C0 N631 C0 N632 C2 N633...
  7. D

    DMG DMU 50 Evolution machine constants

  8. D

    DMG DMU50evo spindle oil-air lubrication settings

    Hi, thank you for the response. Regards John
  9. D

    DMG DMU50evo spindle oil-air lubrication settings

    Hello, thank you for the help, there is 3 tubes from the block and one with just air. I can see 3 tubes end up in the bottom of the spindle base and one in the upper section of the spindle.
  10. D

    Replacement for CL46 oil for MAHO MH600C

    I had the same problem for my machine, it states CLP46 or CL46 but when i googled the recommended oils i found out that they were ordinary hydraulic oils.
  11. D

    DMG DMU50evo spindle oil-air lubrication settings

    Hello, i need advice. What is the right pressure of air in the air-oil lubrication for the spindle and the extra air for the sealing of the spindle. Also in the base of the spindle where the oil-air tubes end up there is a hole that spits oil an air when i start the spindle, is it possible the...
  12. D

    Swapping Heidenhain DDC2 drive controllers to test - Simodrive 611

    the Philips 4022 229 3011 (in out module in the controller) has a similar pot, i thing this is the way to tell the machine what cart is what.
  13. D

    Swapping Heidenhain DDC2 drive controllers to test - Simodrive 611

    When i had made a swap in the DDC2 drivers the axis were wrong, i am not sure but i thing it has something to do with the blue pot. Regards John
  14. D

    Philips, Grundig, Millplus Information Collaboration

    Ihave send you email with my hard drive image it is V4.00 MillPlus from my DMU50evo
  15. D

    DMG DMU 50 Evolution machine constants

  16. D

    DMG DMU 50 Evolution machine constants

    This is how the have made the pipes in the newer versions
  17. D

    DMG DMU 50 Evolution machine constants

    In mine the oil radiator was leaking from the pressure. change the piping so the oil goes first to the exchanger and then to the pump so the heat exchanger wont see hi pressures. the exit from the heat exchanger has a small pipe so all the air goes out first and then the oil. the pump cant push...
  18. D

    DMG DMU 50 Evolution machine constants

    Hi, sorry for the late reply, the fan must blow air up thru the radiators. they turn counterclockwise when you look them from below.
  19. D

    Philips, Grundig, Millplus Information Collaboration

    I have sent you PM.
  20. D

    Philips, Grundig, Millplus Information Collaboration

    Hello, i have send you a link to download the image of hard drive with MillPlus V400 from my DMU50evo. You need Acronis true image to make the hard disc.

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top