FS 1992 FADAL 4020 : Asking $4800 or Best
Looking to sell a 1992 Fadal 4020. Its a DC servo machine with inch ball screws, CNC88 Controller, 10k Hi/Lo High Torque spindle, and rigid tapping. The XYZ axis move quietly and do not make any alarming sounds. The spindle belts are noisy (I can...
For Sale - 1999 Chevalier FSG 618M
Planning to take a 2-3 year break from self-employment to learn a different part of the trade and relocate.
Spindle Runs quiet and the grinder leaves a nice surface finish.
Automatic oiler works well, saddle ways are wet to the touch with oil.
Currently...
Looking to sell My 1999 Hwacheon Hi-Eco 21hs lathe.
It a fairly basic 2 axis cnc lathe with a Fanuc 18T control (I think 18Tc to be precise) It does not have rigid tapping or c axis/spindle indexing, I used a floating tap holder for tapping when needed. It does have synchronized threading...
I've cut a couple of fairly large (~3.25") x 3" long Punches that I will need to make sometime next month. Typically I just wire EDM punches, but in this case I will likely need to make a few Provisionals to adjust the final size as needed.
I was thinking that instead of wire EDMing them I...
I have a couple of 45 degree exhaust elbows made from 2.125 OD 16 gage Stainless steel. I need to add about 10-12 degrees of overbend to them to get the correct alignment.
I tried to make up a set of solid forms to use in a hydraulic press (this method works for solid bar) - but because the...
Looking to sell my Millermatic 211 MIG Welder, It is one of the newer Inverter welders that weighs under 40 Lbs.
I picked up a TIG welder shortly after purchasing this and pretty much haven't used this since. I've only refilled the little argon tank shown in the picture once, so this welder...
Does anyone have experience cutting scroll threads on a 2 axis cnc lathe? (no live tooling)
The width of the scroll would be fairly small - 3mm or 1/8" to keep the tool pressure low , part material would be aluminum or possibly acetal - the parts aren't going to see any appreciable load. Part...
Does anyone know of a supplier that carries 416ss annealed square stock, either 1 1/4" oversized or 1 3/8"? My go to suppliers don't have anything of the sort.
I see McMaster-Carr carries some but the price seems pretty high even by their standards.
These parts were previously being made from...
I see there is a former cat production facility closing up not all that far from me. They have close to 30 Brother Drill Tap machines that they will be getting rid of.
Are parts/wear items like ballscrews, thrust bearings, and spindle cartridges available and reasonably priced? (I'm used to...
What kind of tools are available for keeping track of job related vehicle mileage?
Currently I just write the start/end mileage for work related trips down on a notepad. This has gotten to be a pain because half the time I don't remember to write it down. On several occasions I have ripped the...
Does anybody have any good technical articles on the generation of hsm/trochoid style pocket toolpaths?
Currently, about 75% of the machining that I do is done with homebrew cam software. (it was painfully slow to do it this way at first, but as I've gotten everything working and added more...
I've got a few hydraulic toolholders that I currently run and I find them to be really slick. They are rigid and very noticeably dampen vibrations as compared to ER and even Shrink fit.
I was looking at some cross section pictures of them and it looks like the part that does the expanding and...
I use kennametals KIPR cutters with ceramic inserts for rough hardmilling. Today I had a insert clamp screw break while cutting, sending the clamp flying off into the ether.
The cutter body itself was undamaged, so I just needed to get a replacement clamp and screw. Unfortunately, a "spare...
I purchased a new to me cnc lathe (hwacheon HiEco 21hs with a Fanuc 18t) back in September. Before moving it I had the batteries in the control replaced, so its possible a parameter was lost at this time.
I am just now getting around to setting the machine up. On power up, the machine's...
Does anybody have a source for stainless steel muzzloader barrel blanks?
I checked with most of the big name suppliers (green-mountain, shilen, lothar-walther etc.) But they don't offer anything stainless steel in the correct twist rates. I am hoping to find a stainless 32 caliber barrel with...
I just purchased a new used Hwacheon Hi-ECO 21hs lathe. There is no tag on the machine specifying voltage and I do not have a manual for it, but I am fairly certain it is currently wired for 208 wye 3 phase (still waiting to hear back from the previous owner to confirm) . The power in my shop is...
We need to pick up a small to midsized cnc lathe in the near future.
I just missed out on a machine that I liked at auction (internet literally cut out during the auction), it was a hardinge SV-150. I am looking for other machines similar to this one, we have no preference in brand.
The main...
My Fadal 4020 CNC 88 has been sitting for a couple of weeks. After I Fired it back up yesterday and ran a program, I encountered a problem I have never seen on any other Fadal.
It Changes tools as it should, but the z feedrate during a toolchange is now much higher than it used to be, probably...
Reading Through Michigan's Stay at home order, there is a exemption for those who conduct "Minimum Basic Operations".
This states "For purposes of this order, workers who are necessary to conduct minimum basic operations are those whose in-person presence is strictly necessary to allow the...
Does anybody have a basic but functional design for a vacuum venturi they would be willing to share?
I want to build a vacuum vise for my surface grinder any make the venturi integral, rather than having it hooked up separately.
I just figured I would ask on here before buying one and pulling...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.