What's new

Search results

  1. M

    DP Esprit and Esprit TNG?

    What is the difference between DP Esprit and Esprit TNG?
  2. M

    ordering a new shrink fit device.

    I plan to have a new shrink-fit device for heating the shrink fit holders. what need to be considered while ordering it? what do you think about Easyshrink Evo from SECO? any recommendations? thanks ...
  3. M

    How to program SpiroGrooving?

    How to program SpiroGrooving if I don't have Sandvik software? any tips? Thanks.....
  4. M

    Neutral tool geometric offset in Integrex

    means it will use the value to do calculations when B is 0 to be the right picture. Is this applicable while MAZATRAOL programming only or it is including EIA/ISO as well?
  5. M

    Neutral tool geometric offset in Integrex

    Another question: how do Integrex know the value of nose radius? is it through the probe or via the mentioned tool nose radius value in tool data ?
  6. M

    Neutral tool geometric offset in Integrex

    So is it ok to assign the tool as 45 Deg. tool, then take the offset using probe while B is 45 deg. so in this situation if I run the tool with B0 the tool X will be at edge of radius to angle as the machine adjusting that? No need to take the offset while the tool is in 0 deg. Note that the...
  7. M

    Neutral tool geometric offset in Integrex

    I am wondering if I have a neutral tuning tool (VNMG for example) and use tool probe in Integrex to measure A and B in tool data (tool set as 45 Deg. while measuring). if I wish to run the tool on 0 degree, how do I set the tool in the CAM software should I consider if the tool run with 0 deg...
  8. M

    Mazak Super Flow coolant how to use?

    I have never used the high-pressure coolant before, anyway we have one machine that includes high pressure-coolant pump we run M 131 M100 to 106 to control the pressure. I plan to use the high-pressure while drilling. As first time we use it. Is there anything related to safety need to be...
  9. M

    Peck drill cycle while drilling by carbide

    I am using a carbide drill on 4130 material with high feed and speed, everything is ok and the chips are flying away, but with that we still use a peck drill cycle 1- I am wondering does the peck has any benefits while drilling by carbide? 2- Will the peck cycle hurt the tip of the drill...
  10. M

    Difference between cylindrical boring bar and boring bar with flat

    Thanks, I meant if I install the boring bar inside a socket where the socket is mounted on the turret, this boring bar needs to be flat so it can be hold with the screw? PITA you mean like easyfix from Sandvik ?
  11. M

    Difference between cylindrical boring bar and boring bar with flat

    Hi 1- What is the difference between boring bar with flats and the cylindrical one? 2- If I use CNC turning tool where I mount the boring bar using socket the boring bar should be with flats? Thanks.
  12. M

    Can I use ISO thread insert to do UN thread?

    it's laydown insert
  13. M

    Can I use ISO thread insert to do UN thread?

    Can I use ISO (metric) standard thread insert to do UN thread?
  14. M

    Cycle P9814 for Mazak

    I want to use P9814 cycle to measure the ID not for updating the work offset. If the cycle was done, where can I find the value of the measured ID in Mazak controller? Thanks...
  15. M

    Renishaw Inspection Plus software for Mazak

    Thanks you so much sir The question now if we use G65P9901M***.C***.X**.Y***D***5S***. and G65P9814D3.0 S1.0 is the first one belongs to Go probe and the other one for another method?
  16. M

    Renishaw Inspection Plus software for Mazak

    Hi For VCN machine we have Renishaw Inspection Plus software, however in Fanuc I use probe cycles for updating the WCS i was building the cycle starting from select the WCS and positioning then protected move after that start the cycle, that the usual way I was doing in Fanuc, in Mazak new...
  17. M

    Boring ID jaws

    the size that I turn = the size of workpiece ID the chuck is clamped in reverse?
  18. M

    Boring ID jaws

    I want to clamp 6.5" on ID. So, to turn the jaws do I change the chuck clamp to ID and I turn the jaws till 6.5" ?? is this the way?
  19. M

    Face groove tool for large diameter

    https://www.kennametal.com/us/en/products/p.beyond-evolution-integral-toolholder-face-grooving-external-through-coolant-metric.6124696.html#tad
  20. M

    Face groove tool for large diameter

    if the groove wide is bigger that's will be fine I will I start plunge within limits then will increase until final dia. but as I understand face groove tools have limits (upper dia. lower dia.) and this needs to be considered
Back
Top