What's new

Search results

  1. G

    New to me DoAll G-14 Surface Grinder

    Does anyone have a doall grinder close to this generation? I have a leak in the pilot valve that I can’t seem to figure out. The valve is pictured above. I’d love to see one put together, as I think mine had been messed with in the past by the previous owner.
  2. G

    New to me DoAll G-14 Surface Grinder

    Hey all, there was a significant leak in the valve that controls the table movement, so took it apart and found the oil seal was fubar. Replaced it. I am wondering what these 2 flat head screws are for? They seem to do absolutely nothing. The 4 SHCS are what hold the back cover on to the body.
  3. G

    tear down 10EE backgear

    I'd love to buy some gaskets, but my machine is from 41' and they probably won't fit.
  4. G

    tear down 10EE backgear

    you have to hit the pins from the rear, opposite side of the (what was) threaded portion. What year is your machine?
  5. G

    New to me DoAll G-14 Surface Grinder

    Someone has definitely been into the Selectron controller. I remember when I inspected the unit, the holding power was very weak, which I was hoping due to the fact that the chuck was rusty and dirty, but I don't think thats the case. Anyway, I may have to buy or build a new one. 220V input...
  6. G

    New to me DoAll G-14 Surface Grinder

    Anyone have a schematic for the selectron, or maybe pictures of the inside, of the one they own?
  7. G

    New to me DoAll G-14 Surface Grinder

    You think I run the risk of damaging the seals by using the cost effective stuff from tractor supply? I was probably going to flush the first 5 gallons anyway
  8. G

    New to me DoAll G-14 Surface Grinder

    I found this in stock locally. You think its an equivalent to DTE 25? https://www.tractorsupply.com/tsc/product/traveller-premium-hydraulic-oil-iso-46-5-gal-t806325?cm_vc=-10005
  9. G

    New to me DoAll G-14 Surface Grinder

    Yeah I saw that spec in the manual, but frankly its like German to me. Thanks for the response though. How do you propose I verify seal compatibility?
  10. G

    New to me DoAll G-14 Surface Grinder

    Can you recommend a Hydraulic oil to use?
  11. G

    New to me DoAll G-14 Surface Grinder

    That work. You are the man. Thanks a ton.
  12. G

    New to me DoAll G-14 Surface Grinder

    Hey all, anyone have an idea of how the table and saddle come off this specific surface grinder?
  13. G

    Need help with my new 10EE

    Guys, after putting the motor back together, I have this gap at the front shaft bearing. I don’t remember it being there when I took apart, but can’t be sure. Is it normal?
  14. G

    New to me DoAll G-14 Surface Grinder

    Would I take the table off to access it? The hydraulic pump also sounds low on fluid. I’ll get it home, open everything up and let you know how it goes. Thanks again for all your help.
  15. G

    New to me DoAll G-14 Surface Grinder

    @eKretz i just did another inspection. The cross feed hand wheel is definitely not moving the table. You think it’s an easy fix? The handle on the right should be the cross feed mode selector, with forward being manual mode.
  16. G

    New to me DoAll G-14 Surface Grinder

    Yes it’s running. Thanks I’ll check those out.
  17. G

    New to me DoAll G-14 Surface Grinder

    $300. $372 with tax and commission. Thanks for the manual. When I did the inspection on the unit, the cross feed wheel did not move the table. It was in hydraulic mode. Any ideas on how to switch it to manual mode?
  18. G

    New to me DoAll G-14 Surface Grinder

    Guys Picked up this at auction today for a very good price. Have done a bit of research on them, but not a ton out there. Any insight or info on it would be greatly appreciated...
  19. G

    Full tear down and Rebuild of a 10EE Round Dial

    Yeah, mine were 1/8" NPT
  20. G

    Full tear down and Rebuild of a 10EE Round Dial

    @GrantGunderson, what were these threads?
Back
Top