What's new
What's new
By:
Advanced search…

Search results

  1. S

    SB 13 inch cross feed screw

    This is what I have on non taper attachment cross feed screw
  2. S

    Rockford MV100 Mill

    Very little play 0n y axis shaft. Seems to be between nut and shaft. I've already sealed high low gear box, it leaked into input gear box and leaked out the top. High low gear box has a groove machined in outside to not allow oil and or pressure to not build in input gear box and not cause that...
  3. S

    Rockford MV100 Mill

    No on finding parts. Going to make them Y axis is just a rectangle and X looks to be round. I'll get some bronze and start whittling away what doesn't belong. I'm hoping to find drawings so I don't have to reassemble and assemble multiple times.
  4. S

    Rockford MV100 Mill

    Has anyone removed table or replaced X and Y feed nuts? Y has a lot of slop X not bad, figured Id replace both while I had it apart Pete
  5. S

    What have you made FOR your South Bend?

    just finished a simple steady rest for my sb 13. needed one for a project and started picking up pieces out of scrap pile. turned, milled and welded.
  6. S

    What have you made FOR your South Bend?

    5c drawbar (sorry image is so large)
  7. S

    questions about South Bend 13 Taper

    I've almost completed cross feed screw. Need to drill pin holes for sleeve and handle and to assemble parts to lathe.
  8. S

    questions about South Bend 13 Taper

    Gene thank you. It will be a great help. Thank you, Peter
  9. S

    questions about South Bend 13 Taper

    The other end of feed screw started. Waiting on tool bit to cut internal keyway and gear cutter. Does anybody know if gear is 14.5- or 20-degree pressure angle? Peter
  10. S

    Looking for a 1952 13" crossfeed screw dimensional drawing

    I found this one but doesn't match the screw in my 1965 13. I just took mine apart and copied it. Peter
  11. S

    questions about South Bend 13 Taper

    I've completed taper screw and bed clamp. Bed clamp was modeled off an existing lathe. I'm down to just dial end of taper screw, if anybody has measurements I would greatly appreciate. I haven't cut acme thread end to length yet, waiting to complete dial end. Pete
  12. S

    thank you, my email is, [email protected]

    thank you, my email is, [email protected]
    • sho-me
    • Profile post comment
  13. S

    I read in different post that you had drawings for cross feed screw on south bend 13 with taper...

    I read in different post that you had drawings for cross feed screw on south bend 13 with taper attachment. would you mind sharing them with me? Pete
    • sho-me
    • Profile post
  14. S

    questions about South Bend 13 Taper

    Here is photo of binder stud and chip guard I made. I'm looking for measurements on cross slide screw for taper attachment. that's my next project. Pete
  15. S

    questions about South Bend 13 Taper

    drawing was spot on. thank you again Pete
  16. S

    Rockford MV100 Fenlind Vertical Mill owners?

    I know this is an old post. I picked up a MV100 serial MV432 this winter. Seems like it all works but doesn't have power X feed.
  17. S

    Rockford MV100 Mill

    I know this is an old post, but I picked up a Rockford MV 100 mill serial MV432. Everything works on it. Doesnt have power feed.
  18. S

    questions about South Bend 13 Taper

    thank you for drawing. it is greatly appreciated Pete
  19. S

    questions about South Bend 13 Taper

    binder stud part 5in attachment. south bend number is PT867TF1. thank you guys for your help
  20. S

    questions about South Bend 13 Taper

    I've been purchasing taper parts off ebay and gibs seem a little big. are they custom ground to fit? I've filed and stoned for burs, got one to work but other one won't let screw start and locks up slide. any help is appreciated.

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top