What's new

Search results

  1. Peter from Holland

    cast model engine drawings with accurate dimensions

    In Dutch But a drawing is a drawing Here you can buy drawings of steamengines and motors https://www.modelbouwtekeningen.nl/nl/machines/ Peter
  2. Peter from Holland

    taking .01 off raw stock

    Taking off 0.1'' with a tablesaw ??????? Peter
  3. Peter from Holland

    taking .01 off raw stock

    Thin sheet of rubber Or plywood Or towels Or rags Or whatever soft material available Its about the idea Peter
  4. Peter from Holland

    taking .01 off raw stock

    No It is to even out difference in wide when you put more as one piece in the vice So all pieces are clamped Peter
  5. Peter from Holland

    taking .01 off raw stock

    Clamp some rubber between 1jaw and the workpiece Or in a timesaver perhaps
  6. Peter from Holland

    question about the most suitable connection on a three phase motor on a start stop application

    Triangle or star depends on its input voltage So if you have 220volts input connect the motor to 220volts That is triangle (Delta) in general in Europe
  7. Peter from Holland

    Need help with Error 20 on my Deckel FP2NC Dialog 3

    Martin is local to you Martin is local to you then :D
  8. Peter from Holland

    For Sale Deckel FP4MK 1992

    The Deckel FP4MK is cleaned and checked for all functions to work https://veltmanmachines.com/product/toolroom-milling-machine-deckel-fp4mk-2203-2/ Eighter with a universal table 2038 or a angle table 380Volts 50/60Hz Looking at €17500 EW Located in the Netherlands But we can arrange shipping...
  9. Peter from Holland

    For Sale ! ! !

    And now our Deckel FP4MK is ready too https://veltmanmachines.com/product/toolroom-milling-machine-deckel-fp4mk-2203-2/ Eighter with a universal table 2038 or a angle table Looking at €17500 EW Located in the Netherlands But we can arrange shipping to the USA at competative prices
  10. Peter from Holland

    MAHO lost on Autobahn

    No chains please on a machine and/or a trailer like this Peter
  11. Peter from Holland

    MAHO lost on Autobahn

    In Europe you need a safety chain if the trailer itself has no breaks Generaly below 750kg total weight of trailer and load I have hauled many machines that way Overloaded trailer also The only accident had nothing to do with the trailer or hitch Accidents happen Overkill rigging does not...
  12. Peter from Holland

    Rambaudi Versamill milling machine

    Too lazy to use googletranslate??? Peter
  13. Peter from Holland

    weiler matador gear and pulley feed clutch

    The pulley is locked in place by the seegerring at the back of the bearing as far as I can see The bearing should have a tight fit on the shaft then If not put a seegerring in front and/or use some loctite
  14. Peter from Holland

    weiler matador gear and pulley feed clutch

    Isnt there a setscrew or a seegerring groove to hold the pulley in place ?? Peter
  15. Peter from Holland

    Impossible to machine feature?

    Turn it with a straight shoulder Set it in a vice at the right ange Then a big dovetailcutter Peter
  16. Peter from Holland

    MAHO lost on Autobahn

    A small wire from the handbreak is connected to the car If the trailer and car get seperated that wire pulls the handbreak Then the wire may break But the trailer keeps on the handbreak stopping the trailer That is how it works here Peter
  17. Peter from Holland

    Jung HF50 1965 spindle rebuild

    Flame straightening ??? I have done that on big shafts 120mm or so But this one I would see if I get any succes on a press first Be sure to have the right position where it is bend I do it in V-blocks Support it the same way it was supported in the machine Peter
  18. Peter from Holland

    Jig borer heaven

    I helped constructing a building for a friend of mine to accomadate his Sip/Hauser S50 That was early 90ies Last year they upgraded the machine with new Fanuc controles New servos New drives New PLC New scales for about €150000 Before that they measured the machine Only thing out of spec was...
  19. Peter from Holland

    Jung HF50 1965 spindle rebuild

    It depends where it is bent Can you detect that?? Perhaps hardcrome it all and grind all feautures InTilburg there is e a shop that could do that CZL I do not know how good they are nowadays And how costly Peter
Back
Top