What's new
What's new
By:
Advanced search…

Search results

  1. A

    Unknown older Universal Dividing Head.. B&S style, but Right Hand drive.

    About 11 in swing. 2.75 x 4 TPI Spindle nose, about 1 in long register. Std 40 to 1 ratio. Looked to be #9 B&S spindle taper. No markings other than #276, two Oil locations, and degree marks on OD, and spindle flange.. Fairly roughly machined, a few minor casting flaws. Broken casting by...
  2. A

    Need some measurements off of a 10 in Cincinnatti universal dividing head.

    I have a 10 in universal dividing head (old style.. 2in threaded spindle, #10 B&S taper) It is missing the Quick index plate.. (screws to shoulder on DH spindle nose) Nothing precise, a quick set of caliper measurements is fine.. Need OD, width of outer flange, Thickness of plate where it...
  3. A

    OT Could someone in Minneapolis area, find out how to contact Star Machine & Tool Co?

    OT Could someone in Minneapolis area, find out how to contact Star Machine & Tool Co? Website is up, emails bounce, and phones are disconnected.. Star Machine & Tool - Welcome to our Website! I need a manual for a Star 80V Brake and Clutch relining machine.. They made some nifty shop and...
  4. A

    Looking for info/manual and Tooling. Star Machine & Tool 80V Clutch and Brake riveter

    Looking for info/manual and Tooling. Star Machine & Tool 80V Clutch and Brake riveter Their web site email is dead, as are their phone numbers. Star Machine & Tool - Welcome to our Website! They were in Minnesota
  5. A

    PM website problem

    I get : salam admin, i'm c0rr3c7 ur web site have vuln please check protection again ; ) this is not hack! just alert - with respect, [email protected] When trying to get to Forums page...
  6. A

    OT How come when PM says all cookies are cleared, they are not???

    OT How come, when PM says all cookies are cleared, they are not??? If you are going to leave last page visited/viewed/log in session cookies, SAY SO. PM/vB says "All cookies cleared" when logging out.... At same time, leaving 1 to 3 ea... HTTP cookie - Wikipedia, the free encyclopedia No...
  7. A

    Alaska finally got it's #557 Steam Locomotive back

    Old 557 engine returns but not under its own steam: Alaskana | Alaska news at adn.com Looks like we will have a runner finally.. Here is the story of the guy that bought it for scrap: OHNS: Monte Holm Dead at 89
  8. A

    Anyone have pictures of the SS Meteor

    Like to see the engines and boilers.. Triple expansion 1896 vintage.. S.S. Meteor: The World's Last Whaleback!
  9. A

    As this is a Pro/Make a Living Board, Right Milicron?

    Should we not Limit Posting to FFL, Business Types Only...? Save a lot of Repeat Postings, and get to the good Stuff. Easy enough to put FFL # in Profile... Can't Mention my Green Ch#$% 12 by 36 Lathe, that has Paid for itself doing Fab and Gunwork. Can't depreciate a 20 Year old SB...
  10. A

    Another Country's Abandoned Coal Mining History

    Lots of Pictures, not much Equipment, But Some Works Visible... http://en.wikipedia.org/wiki/Hashima_Island see links at bottom. http://www.ne.jp/asahi/saiga/yuji/
  11. A

    Anybody have tempered spring coil stock (quill spring) by the foot?

    I can buy a whole 200 foot roll of 1/2 inch wide .025 .030 or .032 thick for around 100.00 including shipping...... but only need 10 ft or so .... kind of a waste, unless I want to turn into a Bridgeport M head Quill spring supplier... With only 2.5 to 3 inches of quill travel, not exactly...
  12. A

    Just picked up an M Head

    Bit of a dog, but will blend in nicely in my shop :) B&S taper of course...... but quite a bit of tooling Will have to fire up lathe and make a few things like boring head shanks etc... Much better than crappy old 2 HP Mill Drill, and should look OK next to the Cincinnati Mills :) I will...
  13. A

    Yup Strange stuff going on

    Played with Control panel but other forums work OK...
  14. A

    Req Atlas 7" shaper part info

    I picked up a burnt relic and having more time than money will fix it up. I need the dimensions of the following parts : 9-101-20 Feed screw gear 10-80 4 step drive pulley 9-83 Brake pulley S7-124 countershaft pulley S7-245 Motor pulley S7-86 gear S7-68A Disc and gear (I have T Nut so don't need...
  15. A

    Got a new old mill

    Did a quick search on archives, need info on a Cincinnati #1 Universal Horizontal Mill, It is a cone pulley model and not at this location, I saw it a couple years ago and don't remember Table size, Spindle taper, Speed range, weight etc. Should look kind of cute next to my 2MI looks like it...

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top