What's new
What's new
By:
Advanced search…

Search results

  1. J

    Fanuc 16 G43 behavior

    Hi, We have a machine (Kitamura Sparkchanger 2XiF) with a Fanuc 16 control that recently had to have all parameters reloaded. Now the machine is acting up when G43 is called. If the machine doesn't have a reference return performed for Z the G43 line positions the Z axis relative to it's...
  2. J

    316 CRES pocket with necked end mill

    Hello, Just looking for a sanity check. I am roughing out an undercut cavity in 316 w/ a necked 3/8" endmill. Length below shank is 3.125" and the manufacturer tech support is suggesting a 0.375" axial DOC for 0.06"-0.18" radial DOC. Feed rate of 29ipm and a speed of 2434 rpm. The only...
  3. J

    Flat spindle noses

    Hi, Does anybody have a source for information on flat spindle noses (100mm flat, 140mm flat, etc)? I have looked high and low and cannot find anything. Thanks, Justin
  4. J

    Investment casting stainless steel source

    Hello, We are currently looking to investment cast a 17-4 PH flange that we would normally machine from bar stock . Part is about 6" diameter by 1.25" long. Looking for reputable recommendations for a supplier in the continental US. Thanks
  5. J

    Star CNC swiss alignment procedure

    Good morning. Does anyone have a copy of a modern (from this century) alignment procedure for a SR20R? Our local dealer emailed a procedure but it is for a 90's era machine with a slightly different configuration. Thanks
  6. J

    Capto C6 tool of known size (tool setter calibration)

    Hi, Does anyone know of a source for a "tool of known size" with a C6 shank for calibrating the touch setter? I know that I can put a pin in a collet but I would like something that cannot change. Thanks
  7. J

    Hexagon price check

    Hi, Does anyone know the list price for a Hexagon HP-S-X1H scanning probe? Just trying to avoid getting f&cked. Thanks
  8. J

    PCD insert and interrupted cut

    Has anyone experienced surface finish peculiarities when using PCD and making an interrupted cut? The finish was fine with carbide but is, for lack of a better word, “sandy” with the PCD insert. Switch was made for chip control reasons. The finish from PCD is beautiful everywhere except on the...
  9. J

    CMM fixtures

    Looking for advice on CMM fixture kits for a 28” x 40” x 28” machine. We will be checking a wide variety of parts and 99% are turned parts. Size range from <1/8” Swiss parts to 12” dia x 12” long. I know that itty bitty parts are not going to be well served by a general kit but just wanted to...
  10. J

    Chick Foundations

    My Chick Workholding rep reached out to let me know they are trying to clear out some NOS Foundation plates. I don't know how big the discount is, but they say it's nice. I have no need for one at the moment so I thought I would post them on here. If you're interested, you can contact Chick...
  11. J

    FeatureCam, how do I do this?

    Trying to machine multiple parts from 1 stock (5 parts in a strip). Do I need to make 1 solid with all 5 parts and the "carrier"? Part 2. Same thing, but multiple stocks(5 parts in a strip, two strips) TIA
  12. J

    Okuma Auto Door Integration

    I am in final stages of adding a DIY auto door to one of the Okuma Multus at work. The company purchased the robot interface from Okuma. The company elected to not purchase the auto door option from Okuma. The Okuma robot interface has inputs for door open and door close signals from the...
  13. J

    Citizen/Mitsubishi programming question

    I am modifying a program for one part in a family of parts. I will be using a variable for the length that changes based on dash number. Doing so allows me to have one program for all parts. My question is, can I write the values in MC Data from within the program? I attempted to do so from...
  14. J

    New machine day... tomorrow.

    Santa's flatbed will be at the shop tomorrow morning to drop off my Christmas present from the boss. Needless to say I am excited and have considered going to bed early so I can wake up sooner. I'm going to "Wrustle" it a little bit and leave everybody hanging on what exactly is going to show...
  15. J

    Spindle Repair - Okuma Multus

    The milling spindle on one of the Multus (Multi?) at work has crapped the bed. This is a 10k rpm, oil mist lubricated, integral motor spindle with a Capto C6 interface. I am simply looking for recommendations or warnings regarding spindle rebuilders. I have reached out to the first 5 or 6...
  16. J

    okuma P200 robot interface

    How difficult is it to interface a robot with a P200L control? We are looking at a collaborative robot to load and unload. Okuma wants $$$ for their interface and $$ to install. It is understood that robots are not cheap, but is there a more palatable solution?
  17. J

    Big Plus BT40 tools

    I am looking for side lock end mill holders for a BT40 dual contact spindle. I am not having much luck and neither is the local tool salesman... the only company that has them is Big Kaiser $$$$. Does anyone KNOW another source?
  18. J

    Haas HRTA6 question

    Does anyone know if the tapered portion of the spindle nose on a HRTA6 is removable? There are 6 SHCS inserted into the spindle nose on the tapers bolt circle, but I am not certain of their purpose. Just thought I would check here before I beat the sh!t out of it with a giant ball peen hammer...
  19. J

    Multus circular interpolation

    I'm scratching my head on this... Trying to interpolate a hole in the YZ plane but the machine is interpolating in the XZ plane. I originally programmed with a G19 and it made a slot by moving in X and Z. I have tried G17 and G18 also with no change. I'm stumped but I know that this machine and...
  20. J

    Capto live tooling choice

    I need to start tooling up an Okuma LT2000EX. The Okuma dealer has quoted Sandvik live tooling to accept C4 Capto but they are also offering Velocity tooling. Can anyone speak to the pro's and con's of either choice? I see from the Velocity website that their tools have the bearings run-in at...

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top