On the IHMI control is there a quick and easy way to reset the tool data table so that the tool numbers match the tool pockets?
Machine is 2023 if that matters?
Thanks
I just got a new DNM5700. Earlier in the week I had a rotary table installed.
The guy installing it homed all of the axes automatically. I can't remember how he did it, so that's the question.
How do I get the machine to home all the axes automatically? He hit a couple of buttons to make it...
Also have posted in the Haas forum, but not much luck, so I thought I'd try here:
I have a 97 VF-2 I bought new.
I have never replaced the mounted battery on the maincon? board. I'm not getting any battery alarms and I do not plan on messing with it until I do, I'm just trying to plan ahead...
I have a 97 VF-2 I bought new.
I have never replaced the mounted battery on the maincon? board. I'm not getting any battery alarms and I do not plan on messing with it until I do, I'm just trying to plan ahead.
It looks like the board has two boards in front of it, and for these old ones you...
The batteries in my Lynx220lmsa die without warning and it's a big giant pain in the ass to reset the x,z&b origins.
On my other Fanuc controlled lathes I will get a low battery alarm, change out the batteries while powered up and I'm rolling again.
I'm using good quality batteries and not the...
I moved my 2014 lynx220lmsa and just got it wired back up.
Is there any way to tell if it's phased correctly or if I need to swap 2 wires around.
On the newer Haas mills there is a light in the electrical cabinet that will let you know if you wired right or not.
Does the Doosan have anything...
We have a new to us Jakobsen 824 surface grinder. I'm looking at the way oiling system and from what I can see, it looks like you fill up one side of the tank and drain the other when it gets to the sight glass. Is this assumption correct?
Also, what do you run for way lube in this machine...
Getting this alarm and cannot find any info on it. Nothing in the manuals and no help from giggle. Anyone have any experience with this one?
Sent from my SM-G991U using Tapatalk
I have a Remington 788 and I'm looking at the bolt. It looks like the part the holds and ejects casings is pressed into the part with the bolt handle and lugs.
Is this correct? and has anyone ever taken one apart? If so, how did you get it apart?
The rifle is chambered in 6mm Rem (LH) if that...
Looking at the possibly picking up a 12x24 auto surface grinder.
Leaning towards an Okamoto. With that said what are the differences between the Okamoto 1224 st vs 1224 dx?
I see that the z axis on the st is controlled by a handwheel (and can also be auto fed) where the dx is controlled by an...
Like the title says, my lynx 220 won't ref return the z axis when you hit the button on power up. x & b home just fine, but when you try z the cycle start light blinks and the z axis won't go home, and it's not throwing any alarms..
Also worth noting, I can jog z+ but not z- .
If I g28 w0 in...
Like the title says, I would like to have the x axis position to show zero at the center of an i.d. tool holder that's been zeroed out with a co-ax indicator.
Right now it shows -11.0000 inches at the x-axis CL. I indicated the holder reset turret home going thru the parameter 1815 bit 4...
We have an 1964 Tshudin HTG-400 universal cylindrical grinder.
At the end of the auto cycle the main control lever does not trip to end the cycle and retract the wheel head.
I'm thinking that the sparkout timer control my be shot, any one ever dealt with this?
What was the fix?
Thanks
Guys with sub spindle turning centers, what is your goto tool for part-off operations?
Using a .083w blade type tool now.
Looking for something a little more rigid and something that clamps the insert in.
Never been a fan of the push in blade type that I'm using now.
Would like to stay...
When I use the toolsetter on my lynx 220lmsa all of the tools on the main spindle are off approximately .160 in the z+. Everything on the sub side is fine.
How do I get the toolsetter to zero the tools on the face of the part instead of .160 in front of it? is there a parameter or some registry...
Moving my shop and getting machines powered up at new shop. Having a problem with my 97 vf-2.
Powered it up and I got a dead crt. Machine will go through the power up re start routine and I can jog the axes and change tools using the atc f/r buttons.
Now when I initially powered it up I heard...
Have Chlorinated paraffins been removed from coolants?
Been reading some threads about people unhappy with their current coolants, and it's not just one brand.
There was some info regarding the epa and the push to ban them but the press release on qualichems website is a few years old and...
In the next month or so I'm going to be moving my shop. I have 2 lathes with Fanuc 18t controls.
I have downloaded and saved the parameters for both machines. My plan is to replace all axis batteries before they get disconnected.
My question is in regards to the AA sized battery for the...
Had a thought of building a heavy duty cart to bolt to the bottom of a bridgeport mill so I could roll it where I need it then lock the wheels.
Has anyone ever done such a thing or am i out in left field somewhere?
Sent from my SM-G930V using Tapatalk
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.