We have a small lab mill with a Sinnumerik 808D advanced controller. The machine had a hand lubricator which we replaced with an electrical one. The one we have will pulse occasionally by a setting. However we wish to connect the Lubricant low switch to the control. We found the right...
I seem to have done the biggest mistake in my life by buying a machine with a Siemens Control. I have always had Heidenahin and Fanuc controls in my entire working experience spanning over 40 years. I have bought a lab mill with this control and I wish to get to know how this machine handles...
Have a bridgeport interact VMC with Bosch drives and Z axis turned up a fault on switching on the next day. Apparently the machine had two power transistors faulty and changed, however it is still bringing up fault after some time working. Power off and power on goes and comes back. Anybody...
Have a vertical machining center with a 1KW Spindle motor 1PH6135-4NF49-Z
This motor ahs a RON 350- 2048 encoder fitted. Motor is damaged and need to replace and found an identical motor with same part number.
However this has another type of encoder. ERN1387-2048 although the motor has the...
This morning, our CTX200 CNC lathe presented this problem.
When referencing the X Axis, the machine gave a 510 Alarm Overtravel +X which was very far away from the X overtravel.
Then I powered off and powered on the machine while pressing OPR button + Can.
I tried to reference X. It moved...
This machine started to give up this problem. When machine changes the tool, the tool arm will stop half way with the error TOOL NOT UNCLAMPED. air keeps blowing.. then if you press CE and start button, it would proceed with the tool change and proceed with the program. This would happen with...
We are currently buying pre-cut POM round bar from 200mm to 120mm Diameter in slices of 18 or 30mm. We are being overcharged in weight plus the cutting charge. We do have a mechanical band saw which can handle as large as 300mm in our shop but I know cutting Derlin can be tricky as the blade...
Switched on a Bridgeport VMC760/ TNC 2500B control and a few seconds later I got X motor overheat. I did not even switch on the machine! It ran for the past 6 months every day with no issue and got this when it was restarted. The error comes with the motor cold. I have come across someone...
Have a Gildemeister CTX 400F machine x 2 axis and lost all the parameters in the machine. I managed to put them all in, however the spindle turns and stops immediately.
I need the spindle parameters or if anybody has a similar machine and could give me a copy I would be most obliged. I do not...
Anybody has a CTX400F machine who can send me the machine parameters? lost all the machine parameters and managed to put everything back except the spindle`s parameters. It just runs slowly for a few seconds and stops. The spindle motor and possibly that of the sensor parameters are not...
We have a Gildemeister CTX 400F with a Fanuc 18T Control.
The Machine came up with a lot of errors one morning as if the Battery got flat but apparently the Battery reads the correct Voltage. Anyway we input all the parameters which were eventually downloaded one time from the machine by an...
Anybody knows where the backup batteries in this machine are located?
I found the NC battery but usually there are 3 batteries... The only battery I found is the NC Battery.
Thanks in advance for any help.
We have a Bridgeport VMC1000. The machine has Siemens drives and Haidenhain controls. This machine brings up a spindle drive fault when doing the first spindle orientation when switching on the machine. We usually give the spindle a spin by hand and command M3 or M4 and usually it will spin...
We are machining aluminium plates about 100mm x 600mm x 4mm thick which we affix to a jhttp://www.practicalmachinist.com/vb/images/attach/jpg.gifig and are machining off 0.5 mm from one side with a face mill. The material is previousy cut with a Guilliotine and we believe that this is leading to...
Anybody would recommend where you might get the best priced spare for our agie hss250.
need a UV rubber booth... anybody bought one and was satisfied with the quality and of course the price...
Thanks
Hello,
Have just bought this colcehster machine 2000L. It will jog axis.
it not turn the spindle, move axis or run a program or turn the turret with MDI nor program run.
This has been bought in.... We have quite a number of cnc lathes- gildemeisters, leadwell, harrison....
I simply am beaten...
Hi,
Have a Jones and shipman 4 th axis siezed propably the hydraulic brake but not sure. need a pdf manual for taking it apart, anybody has it?
thanks in advance
I do not use this much. Whenever I used it, it worked but!!!!!
require to repeat a program a number of times and I am using a program like this
I have had to fit a cone in the draw tube and the machine does not signal the end of bar, so I repeat the program the
desired times and machine...
Hi,
Have a CTX400F cnc 2 axis lathe.
This machine has two sensors which monitor the chuck and two which monitor the pressure. There should be a module as well for giving the signal to the CNC which is ok to start the machine.
What is happening, as soon as the chuck closes, after some time, an...
Hi,
We have a gildemeister CTX200F with C axis machnie
and fanuc control which we want to perform C axis tapping in the X axis direction.
We have other similar controls for which we use
G0 X155 Z10
G88 X130 R-2 F50 P0
and works great.
On this machine, the tap would go down and keep on turning...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.