Another Indian video. A bit long but some serious old tech involved. (the shots of the old riveted steam boiler and the man- moveable heat shields...) say what you want, but those are some seriously tough people.
Hello all, a friend of mine has a 13" with a threaded spindle and has asked me to be on the lookout for a three jaw chuck. What thread size should I be looking for on the back plate? (if there are several different threaded spindles I realize that I will need to get him to measure the actual one...
I know that they are available from Wells, a bit too pricey unfortunately at this time. Any help would be appreciated. A print of it or the spec's might help to fab one up or get it made commercially if anyone has that. Thanks, Jim
Hello all, manual specifies 20 SAE. After looking some that can be translated to several ISO ratings. What Mobil DTE or alternate brand would be recommended? Thanks, Jim
Hello all, I posted this on the southbend forum in search of advice and am trying here also.
I bought a 5C collet chuck and L00 backplate from ebay. I don't expect perfection obviously, but surprisingly, the quality of both pieces appears pretty good. I machined down the backplate to fit the...
Hello all, I bought a 5C collet chuck and L00 backplate from ebay. I don't expect perfection obviously, but surprisingly, the quality of both pieces appears pretty good. I machined down the backplate to fit the chuck and got under a thousandth TIR. After taking it off and reinstalling it I have...
Found this while looking for something else, thought it might be of interest. (not mine and I have no knowledge of the owner) Jim Brass / Copper / Steel Stock - materials - by owner - sale
Hello all, thoughts on a collet closer for an L00 spindle please. I am comparing using a handwheel type drawbar unit vs. a dedicated 5C chuck. I don't really want to use the lever type due to the cost, relative complexity ,and having to remove the whole unit for thru-hole operations. This is for...
Hello all, I found this photo on the antique forum an was wondering if the machine in the foreground was a Deckel. It seemed an interesting choice being in a US government installation. Jim
Video is in German, but somehow I ended up watching it and the succeeding one. Those guys were some tough old birds,and they sure had an eye for the grain of the stone.
YouTube
Hello all, trying to reassemble a previously disassembled head. No apparent crash damage,but the quill is extremely tight in its bore. I realize that it should be a close fit but I am pretty sure it should be a sliding rather tan a light press. I have not run a bore gauge through it yet to...
Hello all, anyone have experience with these drives? I am familiar with drives. I am interested in knowing about this particular brand rather than a discussion of the pros and cons of various drives. It will be used to power a Cincinnati mill, 2HP, single to 3 phase, home shop. Thanks, Jim
Hello all, 1/4 hp carbonator type motor on a TIG cooler won't start intermittently. Might work 50 times in succession, not on the 51st. might work 3 times not start the fourth. Well oiled, centrifugal switch has no issues that I can see, it does not appear to occur in the same place on the...
Hello all, I rescued an 18 x 30 130 lb. cast iron surface plate from a friend before it went to the scrap yard. It unfortunately sat out in the weather and has some pretty good rust on its surface. I am razor blading it off and so far no major pits. Any suggestions on bringing it back to a...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.