Mystery tool
Good afternoon all so here is a picture I found while looking at an old wood lathe it may not be associated with the lathe but may be anyway have a look and see what it is.
Good afternoon all so here is a picture I found while looking at an old wood lathe it may not be associated with the lathe but may be anyway have a look and see what it is.
Good morning All,
I just want to verify the angle on the dovetail prior to start milling a new red dot plate there does not seem to be much available out there. Anyway, I want to assure the dovetail 65 degreesis correct.
I have a soon to be a recurring job in the shop cutting a fiberglass carbon composite that they want to run with coolant. We ran about 20 parts yesterday and needless to say it backed up the coolant system pretty good. We tried to use a filter cloth to strain the coolant through but it also...
Ok, I have a MSC Feeler Hardinge clone lathe with a Hardinge C24 chuck mount. I think it is the same as a L series type chuck mount, but there are 4 different mounts in the L series L-00, L-0, L-1, L-2. Question is which L series mount is the same as a C24 Hardinge. I want to order another chuck...
We have a Motion Master 5 axis dual table router for sale.
Axis travels X 60.0" Y 120" Z 48.0" C +- 180.00 deg. A +-120.00 deg. with a Allen Bradley 9/260 control. This machine is in operation daily inquires email me at [email protected]
Ok my son is try to keep a 95 Mustang 3.8 engine running long enough to keep getting around in his job hunt. The transmission has bad seals and requires a fluid top off about once a week. He lost the dipstick for the transmission chances of finding one are rather slim short of a junk yard trip...
OK so we finally set up the TM2P yesterday and tried to run the first program. Run fine right up to the first Z move where we got an error code 3.316. I tried to research this thru the machines help screen and the internet with absolutely no luck finding info about this code. Surely someone...
Shooting light loads to make minor in IDPA with the above pistol sometimes it will not lock open after the last round. I am curious as to which recoil spring it has I do have a selection of wolff springs that may be what I need I just need to know what the stock recoil spring is.
Edit update...
OK,
I bit the bullet and bought an LS XJ2025 tractor with a front end loader and a bush hog I must say I am quite pleased with my purchase. Now I want to put a grapple on the front it has a bob cat quick release type mount. I found several that would fit the bill but finding a loader valve for...
Ok, 2004 F-150 Lariat w/ 5.4 engine 130,000 plus miles. I am getting the following codes P0171 (right bank lean)P0300 (random misfire)P0304, P0305 (misfire detected) and P0316 (misfire occurred during first 1000 rpm). Now before all this I had a P0303 and a P0354 (coil malfunction). My usual...
Ok here goes The door remote on my 2004 F-150 died no big deal I thought, Now twice in the middle of the night it turns all the lights on unlocks the doors and lets the fan run in the ac. So I put a put a new battery in it. I made sure the doors were locked when I retire for the night. Aside...
Getting ready to pull the trigger on a new Haas TM-1P this machine has a 7.5 hp motor and max rpm of 6,000. I need a face mill with Cat 40 tool holder. I'm thinking a 2 or perhaps a 2.5" diameter will suffice plus it needs to versatile enough to switch out the inserts to go from ferrous metals...
So here goes it. Getting ready to introduce old products with new material base namely a carbon graphite fiberglass laminate. Material thickness will not exceed 0.5" but may vary in the actual part by 0.125". Have 3 cnc machines with 10 hp and up to 24k rpm. Being an old chip swarf reader if...
I have some material that management wants to use in one of our products that is very soft as the title says it in the 12 to 22 Shore A durometer range. The endmill must be in a ball nose configuration with a 0.75" diameter. At this time I have been using a Kutzall 3/4" sphere Sphere Burr -...
Good Afternoon All,
Gentlemen, I need a tapered collet extension with a ER-11 collet on one end about 6" long base diameter say 0.750" or 1.00". I have been googling around and have not been successful yet. A link or a point in the right direction would be helpful, did I mention I am planning...
OK so my quality guy stops by and brings me a Starret Last word indicator. I have been partial to my B&S besttest for about 20 years no matter, anyway I open the case and start to check out the new indicator funny it does not spring back to a neutral position. I move the little lever and the...
OK, so doing the mechanical alignment is pretty straight forward I have done this on several 5 axis routers with Allen Bradley controls it is as easy as do the alignment input the compensation values and your done.
Now I am faced with doing this on a 5 axis router with a Fanuc 15 control...
OK, got a leaking upper extension cylinder cannot see the leak, but suspect its a gland seal. Any one have a diagram or illustrated parts breakdown like to know what this looks like before I tear into it. Did a google search and came up with nada. I get this fixed the owner takes down some...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.