My shop is 30 miles from my home (Hey, it was cheap and otherwise perfect). I get out there about once or twice a week. It is in the middle of a run-down mobile home community. It was broken into years ago and cleaned out. Now it is full of machine tools and tooling.
The shop has...
Hey guys, I have a nice small boring bar with an unusual V-shaped cutter. I'd like to get some additional HSS cutter stock for it, but not finding it from the usual suspects. Can you identify this and/or recommend a source? Photos below. .155" wide and .120 derp. I just need a couple
Thanks!
Title should read Rivett 918.
This set is most of the major and minor pieces as shown.
Notably not included are the feed screws and associated hardware, and the gibs.
Everything else appears present, from the bed to the compound.
I'll include a 5" dog drive that is suitable for a chuck...
Allen-Bradley drum switch - Fwd low & high, Rev Low and high.
Original switch from a Rivett 918 (also for sale).
The heavy mount shown is from the 918, not useful unless you are restoring one to original configuration.
Wires left in place as a guide to hookup.
Excellent condition.
$200 plus...
These came from a Logan 12" setup IIRC.
I have an LA591 and 595 blocks - front and rear? 5/8" slot
Also a feed lever and the mounting plate from the later Powermatic setup.
$25 each plus shipping
Email works best
Bullnose Live Center MT4 Good bearing SPF to gbent
Lantern toolpost with 2 toolholders - parting and threading 2.25" square base $90
6" 4-jaw chuck. U.S.A., no brand, looks like Union, good shape, just dirty. I'll clean this up before shipping $100
$10 shipping CONUS on any or will...
South bend Metal Lathe Model 10K
"Light 10" Model A, with long bed.
Quick-change gearbox for threading and autofeed.
Power crossfeed and Z-axis (length) feed.
Reversible motor and leadscrew
Newer Leeson motor,
This lathe has been obviously well cared for in a private shop.
Has been in dry...
2 complete set of shims for 1.5" horizontal milling arbor.
15 Shims range from 1/8" down to a few thousandths
The smallest shim in each pack is bent - see photos
One set New in package, otherset had been unsealed and had some rust, so I cleaned those with evaporust.
one buy gets both sets.
$30
20 assorted spacers and shims for 1-1/2" milling arbor
1.5" down to .002"
Total stack is about 5.5"
All have key slots except the 3 on the right in the first photo
All are clean and in good condition.
The thinnest shims have some typical bends but will flatten out in use.
$50 shipped CONUS...
Top Plate for Hardinge HCNC Turret machinesUses common 3/8" tooling (slots measure .412")
No toolmarks nor damage. Evident stains and streaks from normal usage.
Nice plate in excellent condition.
$50 + shipping
One Set of 3 master base jaws, NEW in original ATS box. Made from hardened steel.
Marked "Schunk (logo) UVB-B315"
Box labeled ATS 11935334
Price $295 OBO
Includes shipping if you don't beat me down on price ;)
Fits 12" wedge bar quick jaw change chucks size 315mm including the following...
Adopted a new project recently. Rivett 918 1941 vintage.
It's a bit rough but the important stuff appears present: Complete compound assembly, plus most of another. 5C collet closer.
Cabinet, motor and drive are missing.
Currently disassembling and cleaning.
I have four backing plates threaded 2"-10 tpi.
These fit Wade and possible other lathe spindles.
2 smaller plates appear shop-made
3.5" OD
.739" thick mounting flange
2.3" x .475" hub
$10 each
4-bolt backing plate,
4.30" OD
3.77" dia register step
Bolt holes 3/8" on 3.19 BC
$25
3-bolt...
I picked up a War Production 9A this morning, Navy markings with a bucketful of tooling. Among it was the contraption pictured below. It looks period correct and the faint paint remnants appear to be SB gray. I cannot find a photo of it on any of the SB catalogs of the era.
The two...
Tapmatic tapping head for larger size taps
Model or SN is milled off (?) No, it's not hot ;)
Max capacity 14MM 1000 RPM
I was told it uses Euro-style collets, though none came with it.
arbor measures 3/4" OD, .425 ID (though it's marked 9/16 on the end). The slip collar measures .870...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.