What's new

Search results

  1. J

    DNM 5700 Air questions

    Hello I have a new dnm 5700 I am hooking up. When the "e-stop" is on does the air still purge thru the spindle? That is how it works on my 2013 dnm 400, with e-stop on, the spindle purge air continues to run. So I had to run a ball valve to turn it off manually. Hopefully on the new one...
  2. J

    FS: Bridgeport Mill Variable Speed SUPER NICE CONDITION!!!!!!!! Servo 150 Power Feed Newall DRO

    For Sale Late 90's Bridgeport Toolroom Mill. Super nice condition, Like new Servo 150 Power Feed. Newall DRO's work perfectly and are super accurate. Like new KURT 6" wide x 9" opening vise. 2 HP Variable speed head. Wired for 220v 3 Phase Very nice tight machine, always in an air...
  3. J

    Speedio firmware upgrade.

    I have read several times where people say their local place is upgrading speedio firmware for free. Both of mine are 2015 models (sx1000) My local place in Cleveland Ohio also told me they would do it for free over 1 year ago. They said they would stop by and do it for free next time they...
  4. J

    Brother Speedio Recovery help for X axis.

    I have a 2015 speedio x1000. Made a big mistake and the backup battery ( 3 AA's) did not get changed in time. I did the recovery procedure, we were able to get the Z axis and Y axis right back to where it was before. The problem is with the X axis, it is now off by -.6293 Touching off parts...
  5. J

    WTB Automatic Saw (central Ohio)

    Looking for a nice small used horizontal automatic saw. Located central Ohio but willing to travel for a nice saw. Nothing large just cutting small parts. Thanks, Joe cell 419-589-four one seven four
  6. J

    Brother Speedio adding a Cycle end Light

    Has anyone successfully added a cycle end light to their Speedio? I would be very interested to hear about it. Thanks! Joe
  7. J

    Vacuum Heat Treater Recommendation Ohio

    I have some small M2 parts I make where the Heat treat is critical. Can someone recommend anyone in Ohio that can run these with care? I am in Mansfield but willing to drive to Columbus or Cleveland. My current Heat treater is doing a great job but the shop is closing. Thanks! Joe
  8. J

    30 Taper Toolholders NMTB Quick Change FOR SALE

    I have a very nice selection of 30 taper tooling I no longer have a use for. A lot of them are BRAND NEW and the rest are LIKE NEW. All quality name brands like Kennametal, Erickson, Jacobs, Apt, etc. Jacobs #3 Holders, 3 pieces all new. Morse Taper Holders: MT1, MT2, MT3, MT4 (1 of...
  9. J

    Remove Manual Guide I from FANUC OMIC

    Has anyone removed Manual Guide I? I use cad/cam and have never had a use for it. Seems all it does is slow my bootup time way down and likely uses up some of the small amount of memory the machine has.
  10. J

    wtb: HARDNESS TESTER ROCKWELL C (Ohio)

    Interested in purchasing a nice rockwell tester. It is for small flat parts I check at approx. 60 RC. I am looking for a Wilson or similar quality. Something within drive of central Ohio would be great. Thanks, Joe
  11. J

    Moving Harig 6 x 18 automatic Surface Grinder

    Just picked up a Harig grinder 70 miles away and plan to bring it home on my heavy utility trailer, trailer is very stout I just want to be sure I have it tied down correctly. I will get a couple long 4x4's or 2x6's and fasten grinder to them. I have a couple very heavy straps I will use also...
  12. J

    Kaeser vs IR Rotary to run 3 Cnc mills

    I have narrowed my new compressor down to 2 choices: A new "IR R5.5i-TAS (7.5 HP)" This is a new model to replace the UP line of IR rotarys. All in one with dryer and 120 gallon tank. IR rep claims these are as good if not better than the Kaeser. Or a new Kaeser SX7.5 with external Dryer...
  13. J

    Good source for quality hand and needle files?

    I am doing a M2 tool steel production job and using up all my old quality Simonds and Nicholson made in the usa files. I am looking for a good source for 8" to 10" good quality mill files and also small needle files. I am sure MSC is the most expensive, I used to buy from Enco when they had...
  14. J

    Doosam DNM and Tramp Oil in Coolant

    Hi, I have a Doosan that I just changed the coolant, I did an extremely thorough job when I cleaned everything and replaced coolant. For one thing, this mill seems to go through the way lube at a very high rate, I estimate I can fill the reservoir with with vactra #2, and it will empty itself...
  15. J

    Source for 5/8" Slow Spiral Drill for Brass

    I have a lot of 5/8" diameter by 4" deep holes to drill in 360 Brass. Previously on this job I just used a 118 deg. jobber drill. Lots of pecking but when drill keeps reentering the cut it grabs. I have TSC but cannot spend $300 for a high end drill, I am thinking a 6" long Slow Spiral will...
  16. J

    sold

    I have a LIKE NEW Haas VF2 For sale. Ebay Link Haas VF2D 2007 CNC Mill Exceptional Condition 1700 Spindle Hours | eBay Seriously interested parties only please can contact me direct on my cell at 419-589-4174 Thanks, Joe
  17. J

    Like New VF2 For Sale

    Hi Guys, I have a like new VF2 for sale. Ebay link Haas VF2D 2007 CNC Mill Exceptional Condition 1700 Spindle Hours | eBay I can be reached directly on my cell at 419-589-4174 for seriously interested parties only please. Thanks, Joe
  18. J

    BT30 Toolholders for Brother, Robodrill etc.

    I am looking into purchasing a Brother Speedio that uses Bt30 tooling. I have zero toolholders this size so would be starting from scratch. Lyndex Nikken seems to be what is recommended most, they are really expensive but I can a discounted tooling certificate to help out. I want to get...
  19. J

    Mini Mill 40 taper with High Rigidity what are my Options?

    I currently have a Haas VF2 and also a Doosan Dnm 400 Vmc. Currently machining some parts from M2 high Speed Steel. The Doosan does wonderful on these parts, tool life is as good as it can get considering the tough material. The Haas is not really up to the job, it has the power since I am...
  20. J

    Source for Squared to Size M2 Blanks for Cnc Mill

    Does anyone know of a source that can provide M2 Blanks squared to size? Blanks size is .250 x 1.003 x .844 Ground to size on .250 and 1.003 dimensions, +-.001 .844 dimension could be milled but must be square within .001 M2 is annealed, looking at 200-300 pieces weekly. Perhaps there is a...
Back
Top