What's new
What's new
By:
Advanced search…

Search results

  1. Milacron

    Mystery power chuck (pic)

    How does this 3 jaw chuck grip material ?
  2. Milacron

    OT- current state of new car buying ?

    In this case, 2024 Nissan pathfinder… discounts off msrp possible ?
  3. Milacron

    WTB - balance arbor for small surface grinder (pic)

    Would look something like this .. 30 degree taper New or used .. Email = [email protected]
  4. Milacron

    Weiler Condor 81 lathe for sale in USA

    Rare bird..in decades of paying attention to such things.....never seen a Weiler like this for sale in this country. From me, on the Bay... https://www.ebay.com/itm/204738050841. cheaper than they go for in Europe.
  5. Milacron

    Weiler Condor toolroom lathe FS ...later 'square head' style...German

    From little 'ol me.... on the Bay. https://www.ebay.com/itm/204738050841
  6. Milacron

    Need 3/8-16 Compression nut

    Most 3/8 compression fittings are 24 TPI....thus the question...would a typical hardware store (ACE, HD, etc) have a 16 ?
  7. Milacron

    Source of small cabinet for grinder, similar to this (photo) ?

    No data plate on cabinet … Global Ind has one similar with drawers but need a door for the application . Dimensions about 18 x 22 x 33 tall
  8. Milacron

    Late model Okamoto "linear" 612 surface grinder.... does the wheel arbor accept Sopko type mounts ?

    or grinding wheel mounts directly on spindle arbor ? (if so, any way to balance the wheel ?)
  9. Milacron

    New "Events" page on PM is live ... did we miss any shows ?

    https://www.practicalmachinist.com/events/ improvement suggestions welcome also. :scratchchin:
  10. Milacron

    PRACTICAL MACHINIST RULES AND GUIDELINES - READ BEFORE POSTING

    OFF TOPIC GUIDELINES OT new threads should be for asking advice or presently advice on a non machining related subject, but, ideally, of a technical nature. Non technically related questions, such as health related are ok if you're desperate or have valuable insights on same to offer. But it...
  11. Milacron

    WTB - Euro or USA made~ 8 inch 3 jaw chuck w reversible jaws

    Manual chuck …Must be new old stock or like new. Plain back is ok. Email - [email protected] with pics and price
  12. Milacron

    Any idea the cost of Schunk Rota manual 3 jaw chucks ? (Photo)

    Like this .. 200 or 220mm size
  13. Milacron

    Weiler Condor 81 vs Condor B lathes ?

    Any of you guys know the difference in 81 and B ? Look the same in photos .,,
  14. Milacron

    Replacement AcuRite scale for 1990’s HLV-EM ?

    Any of you guys know the exact model needed for Z axis ? No nameplate on mine.
  15. Milacron

    lCD video optical comparator for examining drill points exist ?

    ... like a modern tool presenter but only for checking drill point geometry on screen, ideally with graph overlays (for way less $ than a tool presetter). Does this exist ?
  16. Milacron

    HLV-H .... any experience with measuring the bed ways ?

    I ask as I have a Feeler 618 (HLV-H copy) that binds up a little when traveling from headstock to tailstock (test with carriage brake dragging slightly) This would indicate some wear, but there is only .0005" difference in the width of the bed overall, as measured from the top of the bed...
  17. Milacron

    Magnetism gurus.... re coils that shift hydraulic solenoids...

    Parker hydraulic valve with obsolete coil that needs replacing... Found some NOS coils with same outside dimensions/voltage/plug except original is 3/4" bore and these are 7/8" bore. I could make a steel sleeve to adapt...but seeing as how the coil wires would be "further away" from the solenoid...
  18. Milacron

    Source for obsolete Parker hydraulic solenoid coil ?

    This on the Parker valve that operates a hydraulic chuck on Mazak lathe. Parker number 697863. (.75 bore, 100 V AC). Looks like this one at McMaster but theirs is 120 V AC. Search engine brings up numerous links of NOS and used, to purchase one, but no one actually has it (Radwell for...
  19. Milacron

    Recommendations for Y shaped vacuum hose attachment for bench grinder ?

    2" diameter, dust collection outlets are in place now on both sides of bench grinder ready to receive whatever I conjure up... ideal would be Y fitting so that both sides serviced from one hose/one vacuum. Blast gates might be desirable but not essential in this case. Metal or plastic but...
  20. Milacron

    FYI … Google ad sense ads running amuck here of late.. sorry

    Regular advertiser contracts ended a little early this month and the spaces have been invaded by inappropriate ads (and multiples of the same irritating ads) working on cleaning the PM house… sorry

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top