What's new
What's new
By:
Advanced search…

Search results

  1. A

    Alligator Rivet Squeezer

    Anyone know anything about these? This one is American Pneumatic Tool model 745. Connecting air it doesn’t seem to do anything at all. Is it supposed to hammer like a rivet gun or one squeeze type thing?
  2. A

    Oliver Table Saw Fence

    I have this Oliver tilting table saw fence. Not sure which saw it’s for I think 270 but don’t know. It pins to the table pin spacing is 15”. It sure doesn’t fit my 232. Can anyone confirm which saw? I’d like to sell this. Thinking $500. It looks like it’s been repaired but seems fine, see last...
  3. A

    FS: Hauser Jig Grinder

    Looking to sell or part out or scrap my Hauser 3SM jig grinder project. Looks like it was modified at some point I don’t know the history and have never run it. There are cut wires. Everything is in nice condition. I have the covers that are not shown. $800 for the whole thing. Loading is no...
  4. A

    Oster 3D Bolt Threading Dies FS

    Oster 3D bolt threading dies. Some used some were new in the box but the boxes fell apart over time. Some look to have been resharpened, a few chipped. Looking to sell as a lot. Ten complete sets in the following sizes: 1-1/2&2-12, 1-1/4-7, 3/16-24, 3/4-10, 1/4-20, 1&1-1/4-12, 3/4-10...
  5. A

    FS: 8” D1-3 4 jaw chuck

    8” Horton D1-3 4 jaw chuck. I’ve used this chuck on my 10ee, works fine but to be honest this is not the greatest chuck. The jaws are Skinner brand and fit and work but are a bit loose. If they could be tightened up or maybe Horton jaws could be found. In the meantime it’s a workable 4 jaw. $50...
  6. A

    Need to bend hickory

    I need to bend some 1-1/8 square hickory to about an 9” radius. Is there a source for green hickory? Assuming this will need to be steam bent. I can get kiln dried but that might not be flexible enough. What does anyone think?
  7. A

    Threading 25 tpi on Hardinge HLV-EM

    What would be the easiest way?
  8. A

    Wanted Steel Angle

    Looking for fabricated steel angle. 1-1/2 x 1-1/2 x 1/8. Not hot rolled but bent from low carbon steel. The radius is important and needs to be 1/4 on the outside so 1/8 on the inside. 7 ft long, 12 pieces. Seems like it might be a commercially available product but haven’t found it yet...
  9. A

    OT tracking shipment from Australia

    Expecting a box from Australia. I have the auspost tracking number which shows the package getting to US customs, cleared customs and tracked out. That’s it. Who delivers it in the US and what would the tracking number be? I assume it would be usps. Does it get a new tracking number from usps...
  10. A

    FS: Hardinge Headstock

  11. A

    Hardinge HLV-EM Won’t Shift

    Haven’t threaded for a while on my HLV-EM. I can’t get the English Metric or the 1-2-3 selector to move. Took the cover off the back of the headstock and took a look. Obvious how it works, both selectors slide gears on opposite ends of the same shaft. Lube looks good gears turn fine but won’t...
  12. A

    FS: D1-4 Lathe Face Plate

    Several extra holes drilled here and there. Otherwise no problem. Comes with 1/2” Aluminum sub plate if you want it. $100 plus shipping from 53186. Sent from my iPhone using Tapatalk
  13. A

    Thiel Nassovia Bandsaw

    Picked up this cool bandsaw yesterday. I’ve never seen one like it. Cute little guy. Is that an anchor in their logo? Pretty cool. Date on the tag says 1951. Every part even the covers are an iron casting. Amazingly heavy trunion tilts both side to side and front to back. Wheel covers...
  14. A

    FS: Hold Downs

    Didn’t think it was possible but I have too many of these. Dozens of the longer one, possibly hundreds of the shorter. I’m thinking $2.50 ea plus $9.45 for small flat rate shipping. Sent from my iPhone using Tapatalk
  15. A

    FS: M and M Moulder Planer

    Precurser to the Williams and Hussey. 6” two knife moulder. Cute as a bug. Been sitting in my garage forever needs to move on. Single phase motor. Located in Woodland Hills CA (LA area). $350 Sent from my iPhone using Tapatalk
  16. A

    Toyota Forklift Propane Problem

    About 1980 Toyota forklift with 4 cylinder motor. Been on propane all it’s life. Usually reliable but now won’t run consistently. Starts and runs a few seconds, maybe up to 10 seconds, then quits. Restarts right away but then quits. Seems fuel related but don’t know. Replaced the propane tank...
  17. A

    FS: DoAll MP20 Bandsaw

    Turning 60 this year and looking to downsize the shop a bit. I’m selling this DoAll MP-20 bandsaw. This was DoAll’s top of the line saw back in the day. Hydraulic table feed, hydraulic table tilt, hydraulic band tension, hydraulic post adjust, and hydraulic blade speed. You get the idea. Three...
  18. A

    TIG Mild Steel with Stainshield?

    I have a gas bottle here that says Stainshield. I think it's mostly Argon, an Argon regulator fits the bottle. Not sure if this was for TIG or MIG. Anyway, can I use this gas to TIG mild steel?
  19. A

    TNC113 went dead. Where to start?

    Displays flashed on and off for about 30 seconds, then the unit went dark. Opened the unit, nothing obvious. What to do now? I have a meter, scope, etc. and reasonably good at using them. Sent from my iPhone using Tapatalk
  20. A

    FS: Hardinge BB2V Small Vertical Mill Project

    Hardinge BB2V vertical mill project. The machine is reasonably clean and functioning. The drive system is together and complete and working. Electricals are together and working. You will need to add a cord, or maybe a VFD would be nice, or whatever. Motor is dual voltage 220/440 Volt 3 phase...

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top