What's new
What's new
By:
Advanced search…

Search results

  1. M

    Lagun Mill FTV-2 for sale

    Excellent condition -- extra tools ---- Located in Atwater, Calif ---- can hear run ---- 4500.00 Call Mark 209-617-8554
  2. M

    Clausing 1301 for sale

    Clausing 1301 - complete with attachments- good condition- located in Atwater, Ca - is running presently- 3500.00. Call Mark 209-617-8554
  3. M

    American Machine 18x80 for sale

    Located in Atwater , California- there are extras with it - 10 hp - 3 phase will answer and take more pictures if needed. 6500.00 I can't figure out how to use the pictures taken with my I Phone 11--- the error message says file too big ? Mark 209-617-8554
  4. M

    Ames hardness tester penetrator ball wanted

    I need a 1/2 ball like this - Archive for Product categories Penetrators | Ames Rockwell Hardness Testers Mark Leigh --- 209-617-8554 [email protected]
  5. M

    Rebuilt Bridgeport Mill

    I have a 9x42 Bridgeport that was completely rebuilt and painted --low hours -- comes with a X-Y DRO , it is quiet and smooth -- located in Merced , Calif ,95340 will consider delivery -- 7500----- Mark - 209-617-8554
  6. M

    Hypertherm 380 problems

    Was using it yesterday at 220 volts on a 100 foot extension cord -- 10-3 fine wire -- it worked for 2 hours then would only run at 5 seconds at a time with little heat ----- It was doing this when I hooked it up -- I changed the tip parts out to new ones and it ran fine for that 2 hours , then...
  7. M

    What brand Table feed to buy ?

    Looking for a X axis power feed to buy for my BP--- I see they range from 300 to 750 --- what are the pros and cons ? Thanks for your replies :D
  8. M

    How to drop axle and landing gear on trailer to make storage shed

    I am contemplating converting a old diesel trailer with a pair of fixed rear axles and a front landing gear to sit on the ground ---- My question is what have others done to support it while remove the gear and lowering it - DO NOT START WITH WARNINGS --- I have done plenty so far in life...
  9. M

    Speed control on beader

    Is their a way to add a speed control to work off a dial instead of the foot pedal ?
  10. M

    Baleigh bead roller speed issue

    Isn't there a rep from Baleigh that posts here from time to time , I have a new bead roller that I need to modify ---
  11. M

    OT- Want to purchase adapter

    I am looking to buy one of those adapters that enable you to use a drill to power the mill table up and down -- I thought a member here was selling them ? [email protected]
  12. M

    WTB Bolt tap 1 5/16-12

    I need a good used tap to clean up aluminum AN fittings --------- Anybody selling one ?
  13. M

    WTB Bridgeport mill

    Looking for a mill in the Central Calif area or close ----- step pulley or vari drive drive ------ Mark 209-617-8554
  14. M

    Coolant pump for mill

    I have a Bridgeport Textron coolant pump -- works well --- 50.00 plus shipping Can send pics to e mail -
  15. M

    Installing bushings in upper Vari drive pulley 2J2 head

    Is there a suitable glue I can buy locally to install the new plastic split bushings in the upper pulley ? I bought the bushings but didn't get a "kit" , which I find has a two part glue and a mandrel to help set them up - Or should I just order that from H+W ?
  16. M

    Bridgeport 2J2 head --dowel pins missing for belt housing base covers

    I am wondering if the dowels for this --- they say they are tapered on H+W's website ------ can they be bought local - the holes measure about .240 ID 1574 - Taper Pin Any suggestions appreciated-- I am wondering anybody had one they could measure as I can get them overnight...
  17. M

    Bridgeport 2J2 head -- Hi - Lo adjustment issues

    I am working on a 2J2 head Bridgeport---- when I had the motor removed and vari-drive apart to replace the 6010 bearing I placed the selector in the high position. Now with the unit assembled and running ---- it ran fine in high -- I stopped the motor , switched it to low and ran it -- I am...
  18. M

    Belt Specs for Bridgeport Vari Drive

    I have a 880-8M-50 belt here that I thought was for a Vari Drive but it doesn't appear to be looking at the belt that is currently installed there --- My question is -- does the belt above fit any Bridgeport ?
  19. M

    WTB Cold saw

    I am in Merced, Calif 95340 I am looking for a Used Cold Saw , 14 inch preferably but will consider others --- what do you have ? Mark 209-617-8554 or [email protected]
  20. M

    WTB UHMW or any other plastic

    I need to make a pair of 5" x 1.5 wide wheels --- I am open to something larger or would like to buy a box of drops , different sizes , etc Anybody got a pile of drops to sell ? [email protected]

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top