Looking to the folks who have run or repaired grinders for advice. I would normally ask the expert who originally did the work but he sadly is no longer with us:(
I have a KO Lee B360 tool and cutter grinder that had the ways reground and scraped a couple years back. I FINALLY got a little...
Have an 11/16" (0.6875") OD shaft that a needle bearing disintegrated on and ate up. 15thou of wear on the worst of the two journals. The needles run right on the shaft so needs to be ~60HRC. Shaft OAL is ~4". The center ~2" needs to be repaired (the two bearings are 3/4" wide each and have...
Im repairing the apron of a ~1970 Sheldon R15 lathe. Some coolant likely got into it and wore out the pinion shaft (that drives the carriage rack) where it rides on one of its two needle bearings. Its about 15 thou undersized on the one journal. So I need to either repair or remake the shaft...
I have a newly acquired Powermatic 89 metal bandsaw w/ hydraulic feed. Got it all wired up recently and the hyd pump sounds AWFUL. FWD/N/REV handle makes no difference so its not load dependent. Oil height is good and looks really clean.
Sounds like a bad bearing (maybe). Or are they just...
Picked up a decent Supermax YCM30 yesterday. Has an old Dynapath system 10 control thats gotten flaky. Already pulled the dyanpath off and will retrofit something else. If I could get a wiring diagram for the dynapath back panel connectors or the YCM30 cabinet it would save me some reverse...
For sale: Buck 8.25" diameter, 6-jaw, Adjust-Tru chuck. There is an extra set of jaws included.
Things to note:
1) *BOTH* sets of jaws are the same direction (NOT one inside and one outside set - I missed that when I bought it originally.)
2) It has marks/dings as can be seen on both the...
Backstory: I've had a smaller KOLee B360 T&C grinder for a while. The powered work head supposedly uses B&S 11 collets. It has the 11 to 5C adapter for the collet closer. I've had an automatic ebay search for a couple years looking for #11 collets and have never seen one. W/ the 5C adapter I...
Was buying some stuff yesterday and the fellow was liquidating some machines out of an old warehouse. This was in the back (sorry for the poor pics - it was a little dark.) Its marked Vickers Armstrong Engineering Limited. What the heck is it? Some identifying/interesting features:
* there...
Exactly like the title says:) Looking for a Pratt Burnerd Multisize ED15 collet 1-5/8" - 1-3/4". Email w/ pics and price: [email protected]
Thanks!
Stephen
Picked up a nice set of diatest split-ball gauges. Can see the need eventually to be able to measure down deeper holes. Does anyone have one of the extension tubes for sale? In the catalog, they appear to be nothing more than a simple tube w/ a rod inside w/ what I'm guessing has...
Looking for C10 collets. Sometimes called flexi-grip. I think originally made by Balas but later by Sandvik then Somma tools. Email me w/ the sizes you have and price (can email by clicking on my username above).
Thank you,
Stephen
8" Van Norman 2L rotary table. Came w/ a (non-Van Norman) mill I recently bought. Has been sitting on a garage shelf for 10+yrs (w/ some woodworking tools being used). I haven't cleaned it obviouslly, so what you see it what you get. Turns really smoothly. 6 deg per revolution. <10min of...
Well, mostly Hardinge:)
First off the oddball. A Hardinge 2J E2 emergency collet w/ a shallow form milled into it. Looks to have plenty of matl left to bore for something else.
5C collets:
*can no longer read: 3/16, 1/2, 15/16, 9/16, 5/8, 3/8, 1/4
*Royal: 1"
*Sutton: 7/8, 9/16
*Neil...
208-220V, C-face (plus mounting foot), and 3/4" shaft as long as I'm being picky:D Send me an email w/ specs or pics and asking price to sdubovsky AT yahoo.com
Thanks!
Stephen
I've been asking for one for a while over in the classifieds section w/ no luck. So finally decided tried to order new and everyone is out of stock. Inquiring further about putting one on backorder I get responses like "This item has been phased out with no replacement" (MSC's response -...
I have a nice 8" buck 6-jaw that came w/ the lathe but I only have the outside jaws (2 sets actually - 1 has been cut into a bit). They are the 1-pc type. Searching for a set of the inside jaws can leave one w/ sticker shock. Its got me to thinking...
What about cutting/grinding the ugly...
New Starrett 665JZ inspection holder. Only unwrapped to take pics. About $500 new, asking $250 OBO.
Email: sdubovsky *at* yahoo *dot* com (remove asterisks)
www.starrett.com/download/419_p198_202.pdf
Things to note:
1) The indicator glass (plastic) falls out quite easily. In not sure if...
Title says it all. Need it to recut a 55T gear in my sheldon R15 apron. What'cha got? Email is better than PM since the box fills up so quickly.
sdubovsky at yahoo dot com
Thanks,
Stephen
What I believe to be a 5c adapter w/ unknown outside taper. Taper measurements written on it (2.38" OD1, 2.19" OD2, 3.00 taper length). I thought it looked like MT6 when I bought it but its a little too small. There is a pin though it (just above the 3) thats broken off inside but otherwise...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.