What's new
What's new
By:
Advanced search…

Search results

  1. J

    Mitutoyo 6-12" Mic

    PM sent...
  2. J

    Mitutoyo 6-12" Mic

    I dont have a personal account but i believe my work office does.... i will reply in the am... Thanks
  3. J

    Mitutoyo 6-12" Mic

    Very good to excellent condition. I have not had the need to use these for the past 18 months or better. Complete, ready to use.. Shipping cost depends on location, I would assume around $30 to the east coast.. USPS. Money order, check ok... will need to clear the bank $325+ shipping.. reply to...
  4. J

    Kent lathe 17x60 need help! nylon drive feed gear needed

    Thank you guys! We were able to get a manual and the needed gear from Kent. Thanks for the help!!!
  5. J

    Kent lathe 17x60 need help! nylon drive feed gear needed

    Our Kent lathe circa 1990 broke a shifting fork which in turn stripped the nylon drive gear. We dont have a manual so I -don't have the specific part number. If anyone has a manual or by chance any parts, please contact us! Mannex Corp. Clackamas OR Curtis Keller -503-680-2633 This is our main...
  6. J

    WTB 4"-5" 90* face mill R8

    A new job came into the shop in which a 4"-5" 90* R8 indexable facemill would make the job much faster..... Looking for a used setup..... Please reply via PM or straight to personal email.... [email protected] Thanks in advance! Jimmy
  7. J

    WTB 5C machinable pot chuck up to 4.600"

    Mike, Thanks for the info and link! We have orders for other diameters, so I may end up ordering a few from ASMC.... Excellent help!!! Jimmy
  8. J

    WTB 5C machinable pot chuck up to 4.600"

    Thanks for the replies! Doc and Chris: Excellent ideas which we will try. We found a pot collet locally so that will be attempt #1. This is a higher volume job as these are for machines we produce, and each machine uses approx. 80 teflon discs. I have a collet lathe so the production times...
  9. J

    WTB 5C machinable pot chuck up to 4.600"

    Looking for a 5C collet "pot chuck" that can be machined to fit the work. We are turning Teflon into "discs" that are 4.580" round, .187" thick with a 2.300" bore. When they are parted on the lathe, they "cup"... feed/cut rate is good, parting tool is square to the material.. This is the last...
  10. J

    WTB: Comet vari-head mill parts

    Hello, My co-worker owns a Comet brand mill with a vari-speed head that needs a few parts. The parts were ordered through the supplier but what was ordered and arrived are not the same. It's not a simple mis-shippment, we believe the distributor does not know what's up :willy_nilly: He was...
  11. J

    For Sale: Facemills and Linear scale

    I am interested in a few items but your link does not work, as it states a password is needed to sign in. Please post pictures direct or email to: [email protected] I am interested in the used rails and the 406r face mill... JG
  12. J

    Seeking advice on building a tig water cooler tank/pump

    Thanks to all for your help, and a special Thanks to Garwood! I now have a TIG cooler in perfect working order! If anyone needs some CNC machining done, get in touch with Garwood.... I met with him the other day and the shop is set up nicely with CNC mill and lathe. The work was quite nice...
  13. J

    Seeking advice on building a tig water cooler tank/pump

    Doug8cat, I did search several times but came up empty....do you know what the title is?
  14. J

    46 large lathe cutting tools, carbide holders

    I'll be second in line..... PM sent...
  15. J

    Seeking advice on building a tig water cooler tank/pump

    I am going to be purchasing a CK flex head water cooler TIG torch for my Dynasty 200.... (advice on the torch too please) I was a bit shocked with the prices on the water coolers/pumps. The Miller 1 gallon unit is $500 while the 3 gallon unit in over $700. I have a spare 1/4hp motor, and I can...
  16. J

    WTB rem/drop of free machining tool steel 8"x8"x8"

    Thanks everyone! I found a piece of 7" round 10" of 4140 at a friends shop. I was worth the dig through his "left-over" pile.... Plus it only cost me a lunch! :D JG
  17. J

    WTB rem/drop of free machining tool steel 8"x8"x8"

    Mike, You are correct, 4140 would be sufficient for my purpose. I also would not call it a "drop" but my local supplier calls anything that is not in a 12' or 20' length, a drop or remnant piece. I can order a 8"x 8" round from another supplier but the cost is $240. I am looking for a deal for...
  18. J

    WTB rem/drop of free machining tool steel 8"x8"x8"

    Looking for a piece either round or square that can be machined to a finished size of 7"T x 7"L x 7"W. Once machined it will not need to be heat treated. Please email direct for fast response..... [email protected] Thank you!
  19. J

    Any recommendations for Belt Grinders or any "stay away from this brand" stories?

    Why not make one? There is nothing on these units that a novice machinist like myself can't make.... I believe there is a design and build-up tutorial somewhere on this site. There was also a member offering them for sale not too long ago....$1800 is alot in my eyes.. Just my $.02
  20. J

    Kurt vise, steady rest

    Could you take $225 + shipping? PM sent too.. Regards, JG

ABOUT PRACTICAL MACHINIST

With more than 10.6 million unique visitors over the last year, Practical Machinist is the most visited site for metalworking professionals. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. Register for the world’s largest manufacturing technology forum for free today to stay in the know.

Learn more about us.

STAY CONNECTED

Facebook Instagram YouTube LinkedIn Pinterest Twitter Tiktok

Register Become a forum member. Register today.

Sign Up Sign up for our e-newsletter.

© 2024 Copyright Practicalmachinist.com. All Rights reserved.

Back
Top