Very good to excellent condition. I have not had the need to use these for the past 18 months or better. Complete, ready to use.. Shipping cost depends on location, I would assume around $30 to the east coast.. USPS. Money order, check ok... will need to clear the bank $325+ shipping.. reply to...
Our Kent lathe circa 1990 broke a shifting fork which in turn stripped the nylon drive gear. We dont have a manual so I -don't have the specific part number. If anyone has a manual or by chance any parts, please contact us! Mannex Corp. Clackamas OR Curtis Keller -503-680-2633
This is our main...
A new job came into the shop in which a 4"-5" 90* R8 indexable facemill would make the job much faster..... Looking for a used setup..... Please reply via PM or straight to personal email.... [email protected]
Thanks in advance!
Jimmy
Looking for a 5C collet "pot chuck" that can be machined to fit the work. We are turning Teflon into "discs" that are 4.580" round, .187" thick with a 2.300" bore. When they are parted on the lathe, they "cup"... feed/cut rate is good, parting tool is square to the material.. This is the last...
Hello,
My co-worker owns a Comet brand mill with a vari-speed head that needs a few parts. The parts were ordered through the supplier but what was ordered and arrived are not the same. It's not a simple mis-shippment, we believe the distributor does not know what's up :willy_nilly:
He was...
I am going to be purchasing a CK flex head water cooler TIG torch for my Dynasty 200.... (advice on the torch too please) I was a bit shocked with the prices on the water coolers/pumps. The Miller 1 gallon unit is $500 while the 3 gallon unit in over $700. I have a spare 1/4hp motor, and I can...
Looking for a piece either round or square that can be machined to a finished size of 7"T x 7"L x 7"W. Once machined it will not need to be heat treated. Please email direct for fast response..... [email protected]
Thank you!
Cleaning out the clutter.... 3 Armstrong tool holders, No. 20 parting, No. 29L parting and No. 2040 knurling tool. All are in great shape, just dusty. $40 for all, shipped via USPS flat rate priority mail to your door! USPS money order please.. reply and PM to keep it straight. ;)
Thanks! JG
I have a Sheldon 10" lathe that has been modified sometime in it's life, for specific jobs. I now have it with a new job in mind and a turret tailstock would be a great addition. I will modify what I can find to make it work on this particular lathe. I don't need a gem as I can't afford much...
5C air actuated collet closer. It was removed from a shop-built fixer years ago. I have not used it since, I see no reason why it won't work again. No nose cone. 18.5" overall length, 9.75 tube length. Model 3B... Paid $125.... asking the same plus shipping.
Aluminum tray, holds collets and...
I have 60+ 5C collets, some are new, most are used, a couple are worn and I did not count. Mfg, from Enco, Hardinge, South Bend while most have no name on them. All or none, $125... shipping via USPS priority box at cost....USPS M.O. please... sizes are and quantity are:
2) 1/16
1) 3/32
4)...
Hello all and Thanks in advance....
I am looking for help/info/advice on this Sheldon lathe. I am making small production runs in which I hope this lathe will do the job for me. I don't have a manual but it is pretty simple as far as operation goes. The bonnet on the turret does not rotate...
Looking for a small vise to mill a radius on the ends of small parts. Looking for a used, good quality vise like a Palmgreen, Wilton, etc. Please reply with what you have to sell along with condition and price.
Thank You!
JG
Efem G4 (made in Germany) die head with a 1" diameter shaft. I have not used this in several years and since I have another one, I don't need two! It is still in fine condition, operates smooth, by hand. I have the following chasers:
3/4 NPT
7/8x14 (2 sets)
1/4x20
3/8x32
3/8 NC
I will ship via...
Not sure if everyone here would classify this as a "antique" lathe, I guess that depends on how old you are...:D
I posted this in the general forum but with little response, although those that did were helpful. I am interested in finding a second operation/collet lathe to make quantities of...
I have come across this lathe that the current owner knows nothing about. I could use a second operation lathe especially the collet feature. I have searched for information on this lathe here but the threads are too old and the links are dead. I do not know the value of this lathe and the parts...
Cleaning the shop.... Wettstein, similar to the current Shaplane at $350+. Uses 1/4" tool, in fine shape, I just have not used it in the past 5 years. Fits in a standard rocker arm tool post. $125 shipped USPS in the CONUS. As always, if you feel it's too much, let me know. Please reply to this...
Hello all,
I am looking for a good used metric tap and round die set. I can get away with just the taps right now but if anyone has a set they aren't using, I am interested. Would rather pay someone here than ebay or new... The sizes I need are M4x0.7, M5x0.8, M6x1 in a plug chamfer. An oxide...
Hello,
I am looking for a KDK boring bar holder with a 1.5" bore to hold a die head. I believe the 300 series would work... but it you have another option that will slide into the KDK tool post, I could use that too! Let me know what you have and cost.... please email direct to speed up the...
Maybe an odd question for this forum... Not sure where to post it otherwise.... I fabricated a bicycle rack for a local business. Today was installation and my contractor had the issue of using wedge type anchors holding secure in asphalt.
I called a few contractors and suppliers to find out...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.