Armstrong Tool Holders, Cut-off Tool, Knurling tool

[CWC(4)]

As the title states, I have a few older Armstrong tool holders etc.
These are a bit too large for my South Bend heavy 10, so I would assume that they would be fine for lathes with 11/12" swings and larger. Would work well with an old shaper or planer as well.
Included are:
- No. 2R - right hand positive rake
- No. T1-R - right hand neutral rake
- No. 2S - straight positive rake
- No. 2L - left hand positive rake
- No. 2K - Knurling tool
- Armstrong cut off tool with new Armstrong blade
- No. 401 adjustable planer,shaper, lathe tool holder
- Williams 1-1/16" open end wrench

$75. for the lot plus $17.05 med. Flat Rate shipping. Check or MO please. Sorry, no paypal etc.

 

[CWC(4)]

Hard to get a sense of the size of these in my previous post, hope these additional photos help.
Most are about 5/8" wide by 1-1/4" to 1-3/8" tall with about 6" long shank.
I bought these for an old lantern style tool post that I use occasionally. They're too large for that post and sit too high
and quite a bit above the center line of the spindle.
Thanks.

 

[idjeffp]

I would be interested in the 401 tool holder... if you'd be willing to split these up? This is what my 12" Smith&Mills shaper uses.
Thanks Jeff P

 

[rabiedenharn]

I might be interested in the No.2 sized holders. I have a few No.1 sized that I could add as a partial trade, too. (If that interests you, I'll get the details and post pics. I would not be interested in the 401 or the wrench, though.)

 

[SIP6A]

What size HSS blanks do they Take?
Thanks Todd

 

[CWC(4)]

I would be interested in the 401 tool holder... if you'd be willing to split these up? This is what my 12" Smith&Mills shaper uses.
Thanks Jeff P

PM sent

 

[CWC(4)]

I might be interested in the No.2 sized holders. I have a few No.1 sized that I could add as a partial trade, too. (If that interests you, I'll get the details and post pics. I would not be interested in the 401 or the wrench, though.)

PM sent

 

[CWC(4)]

What size HSS blanks do they Take?
Thanks Todd

The 2S, 2R and 2L are all for 3/8" tool bits.
The No. T1-R takes a 5/16" bit as does the No. 401.

 

[SIP6A]

I would be interested in the 401 tool holder... if you'd be willing to split these up? This is what my 12" Smith & Mills shaper uses.
Thanks Jeff P

You should also get the T1-R if you don't already have one these neutral rake tool holders don't show up very often.

 

[CWC(4)]

5 of the tool holders have been sold pending payment.
Here is an updated list:
- No. 2R - right hand positive rake - SOLD
- No. T1-R - right hand neutral rake-
- No. 2S - straight positive rake - SOLD
- No. 2L - left hand positive rake - SOLD
- No. 2K - Knurling tool - SOLD
- Armstrong (No. 22) cut off tool with new Armstrong blade - SOLD
- No. 401 adjustable planer,shaper, lathe tool holder
- Williams 1-1/16" open end wrench

Thank you

 

[rabiedenharn]

5 of the tool holders have been sold pending payment.
- No. 2R - right hand positive rake - SOLD
- No. T1-R - right hand neutral rake-
- No. 2S - straight positive rake - SOLD
- No. 2L - left hand positive rake - SOLD
- No. 2K - Knurling tool - SOLD
- Armstrong (No. 22) cut off tool with new Armstrong blade - SOLD

Thank you

And the check is in the mailbox with the flag up!
Thanks again.
-Rob

 

[shapeaholic]

5 of the tool holders have been sold pending payment.
Here is an updated list:
- No. 2R - right hand positive rake - SOLD
- No. T1-R - right hand neutral rake-
- No. 2S - straight positive rake - SOLD
- No. 2L - left hand positive rake - SOLD
- No. 2K - Knurling tool - SOLD
- Armstrong (No. 22) cut off tool with new Armstrong blade - SOLD
- No. 401 adjustable planer,shaper, lathe tool holder
- Williams 1-1/16" open end wrench

Thank you

PM incoming on the no. 401 planer/shaper tool

Peter

 

[CWC(4)]

I have not heard back from the original responder regarding the No. 401 adjustable planer tool holder, so that and the No. T1-R - right hand neutral rake are still available.
As SIP6A mentioned, you don't see the T1-R style tool often. I was disappointed that this and the #401 were too large for my lathe.
$45. for these two, plus $10.40 small Flat Rate shipping and I'll throw in the Williams 1-1/16" open end wrench.
US addresses only please.
Thank you
SOLD, PENDING PAYMENT
Thanks peter

 

[shapeaholic]

As noted in my PM, I will take them
please advise me how to pay and I'll send you the info on the us address in Ogdensburg NY 13669