Years ago I got lax with backups and went about 4 months without one, My drive crashed I sent the drive (spinning) to drivesavers, They said they couldn't recover any data. I would have paid almost anything to get back all the programming work I had done I even begged them. No luck. they...
I have a Dual Dash Cam front and rear facing... I always have a trailer on so the back cam helps watch that.
I have had good luck with Cheaper Dash cameras and I saw a video explaining how all the cameras use the same internals...(not sure if thats true)
I have used a program called Beamboy 2.2 Its a bit confusing to use but you can set supports (including cantilever), and loads on different beams to see the loads twisting and deflection
For my plasma table and powder coating,... I want really dry air so this has worked for me.
I run a 50' 3/4" Hose from the 80gal compressor along the floor behind my bench and back to a desiccant dryer (old Harbor freight thing) then to a clear bowl type filter oil/water separator then to an...
As I am a part time machinist, I own a soft wash company in NH, Power Wash NH LLC Power Wash NH LLC
Do not pressure wash the roof, It will remove the granulars on the shingles which will shorten the life of the roof.
I recommend hiring a soft wash company like mine to do the work for you...
To adjust ramping,
In the Torchmate cutting software (3 or 4) from the top menu Configuration -> Machine -> Feedrate/Ramping
There are three settings for ramping, We leave the "General" and "Feedrate Move" at 10.00 but we change the "Continuous Contouring" to about 70% of what ever our cut...
are you sure you dont have any binding of the y axis carriage? disconnect the to cap screws on each side and make sure it slides very smooth no binding at all the entire way Also you should be able to spin the inner and outer bearings with your fingers.
We have ours dialed in really good and...
What version of tm cad software are you using?
How are you creating the tool path?
Are you creating a male, female or on path?
Did you setup the material thickness?
How are you exporting the dxf file?
What version of the cut software are you using?
We knotted wire wheel and flap disc thousands of thin (16ga) small parts so I wanted disposable mag chucks.
I bought two 6x12 mag chucks from ebay. They work as advertised.
Anything you do with wire rope (cable) will reduce its strength, This includes using sheaves (pulleys). End termination of any kind will cause stress on it.
Correctly done Wire rope end terminations are very strong see here: Efficiency Ratings of End Terminations
You can get a small chinese...
Is there a way to modify an old thread I started to update the links where the pictures are?
I had to move the pictures and I can't figure out how to change the links.
Not sure about the Teco50,
But If you have a 220 single phase input into a VFD and the VFD is using 10amps to produce what ever 3 phase out,
and you change to 110v single phase input into the VFD, it will take 20 amps in to produce the same 3 phase out.
a VFD is just a highly customizable 3...
I have been through PCI compliance testing as a merchant and as a payment processor. (Many years ago now)
PCI Compliance is a set of security standards implemented by VISA, MC, etc...
These security requirements are put in place to ensure protection of consumers personal and financial...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.