Looking for any help to ID a missing spindle gear (PT30) for a 12-inch model 30. Diameter, tooth count, etc...
A pre-1921 11-inch model 28 "may" have the same gear. The OD of the rear spindle is 1-1/8.
I know this is a long shot, but it's in good shape otherwise.
Here's a super rare lathe in N.J. that needs a new home and some craftmanship work to finish the restoration.
This is a 1932 8-inch Junior, Catalog No. 1308-TB, that was built in 1931 and sold in late 1932. This is a very early 8-Junior with a 2-foot bed. It has 6-1/2 inches between centers...
I would like to purchase a MagnaTurn 612 for a compact lathe retrofit project.
Running or not running is fine, being I will strip it down, replacing the original controls.
I'm Located in Indiana, with-in a couple of states driving time would be nice,
not a must if we can work out shipping costs...
Here is a short clip of the last running feed screw machine from the South Bend Plant.
I purchased this from Ted several years ago and converted it to PLC control for the air saddle, FWD and REV, RPM and the limits.
After this video was made 2 years ago, I added an air dampener control on the...
A website visitor e-mailed me with info on his wide 9, the more I checked, the more intrigued I became that this might be the one to have the S series headstock. I requested photos, and look what came in!
Its a 456-A, B version Standard change gear, HMD bench 9L, yep, 2-1/4 spindle side oiling...
If you have a Wide Bed 9 inch Letter Series R without tapered gibbs
or a T series with Tapered Gibbs, I would like to compare the spud height
on the cross feed nut. I have 9R = 0.3126, 9T = 0.1876
Is this close to yours?
Steve Wells
I have an older machinist made 24 hole simple indexer that uses South Bend # 2 Collets. you would need to adapt to a base
of some type. I had a project in mind when I purchased this, but am not going the use it now. The collet set is most likely
a South Bend CE2432 set of 11 steel #2's by...
I've added a few items to the product list some of you might like, these are of the same
USA made beautiful quality you would expect and affordable too.
The older PT483R2(.437 slide shaft) Heavy Ten taper screw without bearings with a matched 4G fit feed nut:
The newer PT483R3(.375 slide...
Due to high hosting costs, I will be attempting to migrate the SBL Workshop website
to a new server. Over the next week or so, you might experience many broken links
as we upload and reconfigure some files for the new server, please be patience and accept
my apologies in advance for the...
From 2 years ago...yes I might be a little behind...lol
Paula's 1947 Workshop Model A with the very early Transitional Bench Bed feet.
lathe
enjoy,
Steve
I can't remember who sent this file...duh...
I will post credit if you claim it....
Sorry all, but those that create, should be listed for credit.
Send an e-mail to me, with name.
http://www.wswells.com/data/howto/spindle_removal_workshop-9.pdf
Steve
I have added files in the Mill section of the The SBL Workshop - Home website, these were provided
by Rocco Falato and are very nice scans...thanks to RF for his hard work, he also scanned
a complete 1930 HTRAL...it's uploade in the HTRAL section, warning...it is a large file, like
70mb. I also...
This front bearing casting appears to be half drilled in the wrong
location for the rear oil hole return. The original angle is also incorrect.
Does anyone have any photos of the correctly drilled journal and
opinions of a correction for this one? If I make a mistake here, I
will drill through...
I posted this on the Yahoo group also:
As some of you know I have been working on reviving the original
Teflon grease South Bend had made for the headstock and back gears.
I have completed the process and now have filled the first case of
grease. I have 19 left from that case. This is a great...
I picked up a new Infrared lamp to force dry my paint, it being a little cool in the shop.
I thought you all might want to see, it is an American made product by Infratech.
http://www.wswells.com/photos/1968-10L-swells/1.JPG
http://www.wswells.com/photos/1968-10L-swells/2.JPG
Long story...
I have an e-mail request for help on the clutch assembly of a 9A, photos or assembly
prints. The clutch came apart while he was cleaning his apron. I have searched and I don't
have photos of the clutch apart or in assembly. He has PL-902D, and would like clearer
assembly instructions.
Thanks...
here's a deal if the bed is not worn too badly:
Buy it now $750.00 with extra parts, someone should grab this before it gets parted out!
http://cgi.ebay.com/1940-Southbend-Heavy-Ten-Lathe_W0QQitemZ320414985255QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item4a9a38ac27&_trksid=p3286.c0.m14
Picked up my little 2-1/2 foot Stubby today, it looks to be in all original condition and used
very little. Spotting is intact on the flat ways and there are no wear ridges on the V-ways,
spotting can still be seen on the rear V-ways, I'm very happy, I think it will clean up nicely.
The lead...
Jim B's Workshop 405 Crossfeed large dial conversion has been uploaded and is ready for
viewing. This is a great read and I thank him for doing this for the group members to see.
Link to the project index:
http://www.wswells.com/projects/projects_index.html
Direct link to Jim's Project...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.