Hi guys, am fancying a used H.T. oven that was built to handle 460 V 1 phase, 14A
Up here we have power coming into the buiding at 600V, 3 phase.
We use quite a few step down transformers for our machine tools, but always 3 phase in and 3 phase out. Only single phase we have in building is the...
Hello guys, this being Sunday I haven't reached out to Hardinge yet but wondering if they have repair parts available to replace the threaded portion that holds onto the 5C collets inside that rubber hand wheel speed chuck of Sjogren model ? Ours has quite a few years under it's belt
and is in...
Hi all, looks like I may of scored an M&N 200 ton press somewhat local to me up here.
Am looking for a scan of or an older brochure / manual for anything from them to gain some insight
as how they were intended to be used. Of course we'll do our own thing and figure it out
but it's always cool...
Hi, am looking for a used hobbing press running or not anywhere from 100 to 500 tons capacity. Would like a machine with as small a footprint as possible. I've seen names like Mario DiMaio, Ferrera and M&N out there.
Feel free to DM me thanks !
Hi, as title says looking for a blue box micro disc system for our QT8N with T+.
Want to be proactive and have our parameters on the ready if ever there's a mishap.
From what I was told this unit can also store some part programs is this so ?
Am trying to buy one locally here in Montreal but...
Hi there,
As title says.
We have a fibre laser marking machine at our disposal and I was wondering
if the marking process could damage the linear scale on said tool.
Never crossed my mind to do this before but we have a new hire and we thought
it was about time we ID our personal and general...
Hi Guys,
Need some advise as I discovered some wear on our Kent surface grinder we bought new in year 2000. This machine gets cleaned weekly, has hand pump lube and gets taken apart for a deep clean and lube every 5-8 years or so. However a new job came in about 8 years ago and one of our good...
Hi there group, been reading and researching here for the past two months and have learnt quite a bit. What it boils down to is our Colchester Student 1800 has gotten beyond economical repair ( worn quick speed gear change mechanism and noisy headstock ) and is being replaced with a newer used...
Passing along what looks to be a near mint Standard Modern 1334 lathe 220V single ph. in Alberta off of Kijiji. We went another route with a local to us Harrison VS330TR and will be sticking with it ( and regrind the bed ways.. ) That Standard Modern 1334 sure looks sweet ! ...
Anyone know where I can purchase these small bulbs ? Someone already had the same idea and took the remaining good ones from the other less used buttons.
Hello friends, curious to know how long it should take to turn out a quote on custom tooling and or job shop work ? Many of our present accounts seem to require quotes back within a couple days ( 3 ) or a week latest. However I've run into some types that are hot to trot and expect quotes back...
A little background :
-Former Northern Electric ( Nortel ) Ottawa R&D dept. machine
1967 low to medium hours, great shape
-We installed 2010 and all oils-grease-coolants were changed
-Machine ran an average of 2 full days a week at first and now almost daily 8-10 hours shifts, religiously oiled...
Today I was talking on the phone with one of our big customers.
I seldom allow myself to get too friendly as it usually shoots
me in the foot : What I casually mentioned was a neet job we
worked on over the weekend to meet a rush dead line and how I
was feeling a little tired today. Customer...
Hello all !
Was hoping someone went through this before so I know where to start :
Colchester student 1800 with taper att. 80's vintage, nice machine
Feeds stoped running last week. Traced it to a dead worm gear in the apron.
Basically the feed rod turns merrily away while the worm gear that...
Gambin France model 27 univ. mill : free or scrap remove at your cost
Located in outskirts of Montreal in my neighbors shop.
Powered up and still running well, huge mill about 1.5 to 2 x an FP4
Table is approx. 5 or 6' wide.
Universal swivel type head, in vertical mode presently
Headtube about...
Hello again,
Riggers came this morning and we skated the machine over
into it's permanent position. I could not find the pads that
would of come with the machine. Either they were lost in
transport or the machine never had any. The base has 6
leveling screws. 4 near headstock and two on the...
This website or its third-party tools process personal data (e.g. browsing data or IP addresses) and use cookies or other identifiers, which are necessary for its functioning and required to achieve the purposes illustrated in the cookie policy. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.